03.96
Index-324
 Siemens AG 2000 All Rights Reserved
SINUMERIK 840D Installation and Start-Up Guide (IAD) – 04.00 Edition
Proportional gain, 10-241
Protection level concept, 6-90
Protection levels, 6-90
R
RAM memory
Dynamic, 6-103
Static, 6-104
Redefinition of protection levels, 6-91
Reference point approach, 6-138
For incremental measuring system, 6-138
With distance-coded ref. markers, 6-139
References, B-311
Referencing with absolute encoders, 6-139
Regenerative feedback , 2-21
RESET, system settings, 6-178
Reset time, 10-242
Restart, 6-115, 7-183
Rotary axes, limitations, 6-123
Rotary axis
With machine-mounted rotary encoder, 6-119
With motor-mounted rotary encoder, 6-119
Rotary encoders, 6-118
Rotor position identification, 6-160
S
Saving user data, 11-268
Scaling machine data, 6-106
SDB, 3-60, 3-64
SDB210, 3-51
Self-optimization, 10-236
Series start-up file output, 11-263
Series start-up or area-specific archiving, 11-246
Set HHU, 3-51
Setting data, 6-87, 11-284
Handling, 6-89
Setting interface parameters, 3-53
Setting the axis-specific setpoint parameters,
6-114
Setting the axis-specific setpoint/actual value pa-
rameters, 6-114
Setting the MCP interface, 3-39
Setting the MCP/interface to customer operator
panel, 3-39
Setting the reduction ratio, 3-49, 3-63
Shielded signal leads, 4-73
Sign-of-life monitoring, 7-183
Simulation axes, 6-129
Software, 1-15
Software limit switch, 6-134
Software update, 12-285
Special axes, 6-108
Speed control loop, 6-126
Interference frequency response, 10-213
Reference frequency response, 10-213
Setpoint/disturbance step changes, 10-214
Spindle
Encoder matching, 6-142
Monitoring, 6-148
Parameter sets, 6-141
Positioning, 6-145
Setpoint adjustment, 6-144
Speeds, 6-144
Synchronization, 6-146
Test, 9-200
Spindle configuration, 6-142
Spindle data, 6-140
Spindle definition, 6-140
Spindle number, 6-140
Spindle operating modes, 6-140
Spindle speed, 6-148
Spindles, 6-108
SRAM, 6-104
Standard 840D version, 1-16
Standard application, 3-38, 3-40
Standard bus addresses, 3-43
Standard configuration, 3-38
Standard files, 8-188
Start-up, linear motor, 6-154
Start-up of NCK I/O devices, 6-150
Start-up tool
Aborting measuring functions, 10-210
Analog output, 10-204
Circularity test, 10-204
Fourier analysis, 10-204
Frequency response measurement, 10-211
Gantry axes, 10-221
Graphic display, 10-219
Hardware requirements, 10-205
Measuring functions, 10-204, 10-207
Software requirements, 10-205
Starting, 10-206
System requirements, 10-205
Trace function, 10-222
Start-up tool, instructions for use, 10-204
Start-up tool|installation, 10-205
Start-up design concept, Example, 6-96
Start-up sequence, 5-76
Start-up tool, 5-84
Status display during power-up, 5-82
STEP7 Tools, 3-38
Storage of text files, 8-188
Syntax for alarm text files, 8-192
System data, 6-99
Basic settings, 6-99
Control time cycles, 6-99
T
Terminating the start-up tool, 10-206
Testrun preconditions, 9-197
Text file for cycle alarm texts, 8-192
Text file for PLC alarm texts, 8-193
Three-conductor connection (standard circuit),
2-27
04.00
Index
To Next Page
Loading...
Need help?
General
