Tektronix TG8000

Index
F
Factory default settings
HD3G7, 3-212
SDI7, 3-337
Fan fault
beeper control, 2-31
Fan fault alarm, 2-21
FAULT LED indicator, 2-5
Features, 1-1
Figures Of Merit (FOM), 3-105
File trans
fer using FTP, 2-67
Flash m emory, 2-34
Font file installation, 3-297
FORMAT button, 2-2
FRAME RESET 1, 2-20
FRAME RESET 2, 2-20
FRAME R
ESET 3, 2-20
Frame reset signals, 2-20
FRAME RESET STATUS
submenu, 2-26
Front panel
disable, 2-31
Oper
ation, 2-1
FRONT PANEL ENABLE
button, 2-2
FTP file transfer, 2-67
Functional checks, 1-16
AG7, 1-16
AG
L7, 1-17
ATG7, 1 -19
AV G 7 , 1 - 2 1
AWVG7, 1-23
BG7, 1-24
DVG7, 1-25
GPS7, 1-26
HD3G7, 1-36
HDLG7, 1-39
HDVG7, 1-40
SDI7, 1-41
G
General Purpose Interface
Mainframe See GPI
GPI
Mainframe, 2-50
GPI port, 2-6
GPS Synchroniz
ation and
Timecode module See GPS7
GPS7
10 MHz connector, 2-14
ALARM DELAY
submenu, 3-146
ALARM TIME
submenu, 3-145
ANTENNA connector, 2-13
Antenna power, 3-131
Antenna system, 3-103
BLACK 1 connector, 2-14
BLACK 2 co
nnector, 2-14
BLACK 3 connector, 2-14
BLACK submenu, 3-122
DIAGNOSTICS
submenu, 3-152
DST SCHEDULE
subme
nu, 3-139
EPOCH SELECT
submenu, 3-145
Factory default
settings, 3-154
Functional checks, 1-26
GPI
submenu, 3-150
GPO submenu, 3-151
GPS SETUP submenu, 3-130
HD TRI-LEVEL SYNC
RATE submenu, 3-69,
3-126
J
AM SYNC submenu, 3-143
LEAP SECOND
submenu, 3-144
LTC submenu, 3-148
LTC TIMING
submenu, 3-150
LTC/GPI connector, 2-13
Main menu, 3-113
Operating procedure, 3-99
Oven calibration, 3-100
POWER indicator, 2-13,
3-131
Product description, 3-98
PROGRAM TIME
submenu, 3-142
Rear-panel connectors, 2-12
REF IN connector, 2-14
REFERENCE
submenu, 3-118
TIME OF DAY
submenu, 3-133
TIME ZONE OFFSET
submenu, 3-138
TIMECODE su
bmenu, 3-127
VITC submenu, 3-129
H
Hardware installation, 1-6
HD Dual Link Video
Generator See HDLG7
HD3G7
ANC PAYL
OAD
submenu, 3-201
Ancillary data payload
example, 3-206
AUDIO (EMBEDDED)
submenu, 3-193
CALIB
RATION
submenu, 3-211
DIAGNOSTICS
submenu, 3-209
Factory default
settings, 3-212
Fu
nctional checks, 1-36
HD SDI IN connector, 2-15
Installing enhanced signal
sets, 3-171
Main menu, 3-185
Modifying a Zone Plate
Signal, 3-173
MOVING PICTURE
submenu, 3-192
Operating procedure, 3-159
OUTPUT MODE
submenu, 3-191
Product description, 3-158
Rear-panel connectors, 2-15
SECONDARY OUTPUT
submenu, 3-208
Select sample structure and
depth, 3-164
Select the output mode, 3-163
Select the signal
format, 3-164
TG8000 Multiformat Test Signal Generator User Manual Index-3