Toshiba B-EX4 SERIES - Page 102

5. SYSTEM MODE EO18-33027
5.3 DIAG
5-6
*1: B-EX4T2, B-EX6T2, and B-EX4D2 only
*2: Supported by the B-EX4T1-G/T-QM/CN with firmware version of C1.4 or later.
*3: Supported from firmware version of V2.0B for the B-EX4T1-TS25-R.
*4: The way to print the ribbon motor drive voltage fine adjustment values is different depending on the model.
Model
Printout
B-EX4T1-G/T-QM/CN C1.2 or later
B-EX4T2-G/T-QM/CN C1.2 or later
B-EX4T2-H-QM/CN C1.1A or later
B-EX4D2-G/T-QM/CN D1.1 or later
(RIBBON WIDTH TYPE1)
RBN(FW) +0 RBN(FW) +0
RBN(BK) +0 RBN(BK) +0
(RIBBON WIDTH TYPE2)
RBN(FW) +0 RBN(FW) +0
RBN(BK) +0 RBN(BK) +0
Other than above
RBN(FW) +0 RBN(FW) +0
RBN(BK) +0 RBN(BK) +0
*5: Supported from firmware version of C1.2 for the B-EX4T1/EX4T2-G/T-QM/CN, C1.1A or later for the B-EX4T2-H-QM/CN,
and D1.1 or later for the B-EX4D2-G/T-QM/CN.
*6: Supported from the B-EX4T1-TS25-R V2.2
*7: If “CN” is selected for the parameter clear destination, the ENERGY TYPE parameter is not displayed and unable to be
set in the system mode and user system mode. However, the following default value will be set after a RAM clear and
printed on the diag. print label.
Applicable model
Thermal transfer
Thermal direct
B-EX4T1-G/T-QM/CN C1.5 or later
SX compatible
Standard
B-EX4T2-G/T-QM/CN C1.3 or later
Multiple type
Standard
Print condition:
Label length
490 mm to 530 mm (depending on the model)
Print method
User setting
Sensor type
None
Speed
(203 dpi)
B-EX4T1-G, B-EX4T2-G, B-
EX6T2-G, B-EX4D2-G
6 ips
(300 dpi/305 dpi)
B-EX4T1-T, B-EX4T2-T, B-
EX6T2-T, B-EX4D2-T
5 ips
(600 dpi)
B-EX4T2-H
3 ips
Print count
1
Issue mode
User setting
Other
No rewinder motor activated
<< COUNTER >>
Item
Content
Range
Counting condition
TOTAL FEED
Total label distance covered (cannot be
cleared)
0.0 to 3200.0 km
Counted when the paper feed motor are driven to feed a paper or print. (Reverse feed is also counted.)
When the power is turned off, the label distance of 50.0 cm or less may be rounded down when backed
up.
FEED
Label distance covered
0.0 to 3200.0 km
Counted when the paper feed motor are driven to feed a paper or print. (Reverse feed is also counted.)
When the power is off, the label distance of 50.0 cm or less may be rounded down when backed up.