YASKAWA GA800

3.9 Braking Resistor Installation
132 YASKAWA SIEPC71061737D GA800 Drive Technical Reference
Table 3.18 200 V Class
Drive Model
Braking Unit
(Qty)
Drive Terminals
Recomm. Gauge
(AWG, kcmil)
Applicable Gauge
(AWG, kcmil)
Ref.
2257
CDBR-2022D
(× 2)
Specified Wire Gauge
+3 10 × 2P 10 - 8 × 2P Figure 3.73
- 10× 2P 10 - 8 × 2P Figure 3.73
Applicable Gauge
*1
+3 1/0 × 2P 4 - 1/0 × 2P Figure 3.74
- 1/0 × 2P
*2
4 - 1/0 × 2P
*2
Figure 3.74
2313
CDBR-2110D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.73
- 3 3 - 2 Figure 3.73
Applicable Gauge
*1
+3 1/0 × 2P 4 - 1/0 × 2P Figure 3.74
- 1/0 × 2P
*2
4 - 1/0 × 2P
*2
Figure 3.74
2360
CDBR-2110D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.75
- 3 3 - 2 Figure 3.75
2415
CDBR-2110D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.75
- 3 3 - 2 Figure 3.75
*1 This is the applicable wire gauge when you use a braking unit other than Yaskawa braking unit (CDBR-type).
*2 This is the applicable wire gauge when you use the same wires for terminals - and +3.
Table 3.19 400 V Class
Drive Model
Braking Unit
(Qty)
Drive Terminals
Recomm. Gauge
(AWG, kcmil)
Applicable Gauge
(AWG, kcmil)
Ref.
4208
CDBR-4045D
(× 2)
Specified Wire Gauge
+3 10 × 2P 10 - 8 × 2P Figure 3.73
- 10 × 2P 10 - 8 × 2P Figure 3.73
Applicable Gauge
*1
+3 1/0 × 2P 4 - 1/0 × 2P Figure 3.74
- 1/0 × 2P
*2
4 - 1/0 × 2P
*2
Figure 3.74
4250
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.73
- 3 3 - 2 Figure 3.73
Applicable Gauge
*1
+3 1/0 × 2P 4 - 1/0 × 2P Figure 3.74
- 1/0 × 2P
*2
4 - 1/0 × 2P
*2
Figure 3.74
4302
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.73
- 3 3 - 2 Figure 3.73
Applicable Gauge
*1
+3 1/0 × 2P 4 - 1/0 × 2P Figure 3.74
- 1/0 × 2P
*2
4 - 1/0 × 2P
*2
Figure 3.74
4371
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.75
- 3 3 - 2 Figure 3.75
4414
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.75
- 3 3 - 2 Figure 3.75
4477
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 3 3 - 2 Figure 3.76
- 3 3 - 2 Figure 3.76
Applicable Gauge
*1
+3 3/0 × 4P 2 - 4/0 × 4P Figure 3.78
- 3/0 × 4P
*2
2 - 4/0 × 4P
*2
Figure 3.78