YASKAWA LA500 - Page 372

372 YASKAWA SIEPYEULA5001C LA500 Technical Manual
oL2 ..................................................................... 179
Protection Functions ............................................ 342
oL3
Fault ............................................................... 179
Minor Fault ....................................................... 187
oL4
Fault ............................................................... 180
Minor Fault ....................................................... 187
On-Delay Timer ...................................................... 285
Ope Select @Keypad is Disconnect ............................... 351
oPE01 .................................................................. 190
oPE02 .................................................................. 190
oPE03 .................................................................. 190
oPE08 .................................................................. 190
oPE10 .................................................................. 191
oPr ...................................................................... 180
Options................................................................. 233
Output Phase Loss Detection
Protective function .............................................. 340
Output Phase Loss Detection Time
Alarm Settings ................................................... 343
Output Terminals ...................................................... 58
ov
Fault ............................................................... 180
Minor Fault ....................................................... 187
ovEr .................................................................... 187
Overtorque detection
Parameter ......................................................... 334
P
Parameter
Access Level Selection ......................................... 280
Automatic selection ............................................. 283
Backup (drive to keypad)....................................... 102
Changing setting values......................................... 102
Checking modified parameters ................................ 101
Delete Backed-up Parameters.................................. 104
Restore (keypad to drive)....................................... 103
Setup mode ....................................................... 101
User-set ........................................................... 283
Verify (keypad and drive) ...................................... 103
Parameter Change .................................................... 352
Parameter Setting Errors ...................................... 168, 190
Password
Setting............................................................. 282
Verification ....................................................... 282
PC
Connection procedure............................................ 64
Peripheral Devices ................................................... 233
PF................................................................. 180, 187
Protection Functions ............................................ 340
PF dv/dt Level ........................................................ 344
PF Min Current ....................................................... 344
Phase Order Selection ............................................... 285
Power loss
with Built-in EMC Filter ........................................ 33
without Built-in EMC Filter..................................... 32
Programming mode ................................................... 82
Protection Functions
DC bus undervoltage............................................ 329
Drive Overheating ............................................... 339
GF.................................................................. 341
Ground Fault Detection......................................... 341
HCA .........................................................343–344
Input Phase Detection........................................... 340
Motor Overload .................................................. 327
oH.................................................................. 339
oH2 ................................................................ 339
oL2................................................................. 342
Output Current Overload .................................343–344
Output Phase Loss Detection Time ........................... 343
Overload .......................................................... 342
PF .................................................................. 340
Software Current Limit Selection ............................. 342
Uv1 ................................................................ 329
Protective function
LF.................................................................. 340
Output Phase Loss Detection .................................. 340
Pulse Train Input/Output
Parameter ......................................................... 326
R
Rating (Three-phase 200 V)
Drive............................................................... 224
Rating (Three-phase 400 V)
Drive............................................................... 225
rdEr..................................................................... 195
Remove
Front cover ........................................................ 34
Front Cover........................................................ 34
Keypad ............................................................. 36
Rescue Operation...................................................... 96
RESET key ............................................................. 77
Residual Current Monitor/Residual Current Device
RCM/RCD......................................................... 67
Wiring .............................................................. 67
Restore
Parameters (keypad to drive)................................... 103
rF ....................................................................... 181
rH ....................................................................... 181
RJ-45 connector ....................................................... 77
rr ........................................................................ 181
RUN indicator ......................................................... 77
RUN key................................................................ 77
S
SC ...................................................................... 181
SCF..................................................................... 181
Setup Procedure for Elevator Applications ........................ 92
Accel Ramp and Jerk Settings .................................. 94
Brake Sequence ................................................... 95
Decel Ramp and Jerk Settings .................................. 94
Down Commands................................................. 92
Inspection Operation ............................................. 95
Multi-Function Terminal Setup................................. 94
Rescue Operation ................................................. 96
Speed Reference Selection ...................................... 92
Speed Selection ................................................... 92
Terminal Setup .................................................... 94
Up Commands .................................................... 92
Side-by-side
Derating........................................................... 342
Slip compensation
Parameter ......................................................... 292
Softcharge Relay Maintenance Set................................. 355
Software Current Limit Selection
Protection Functions ............................................ 342
Speed Agreement
Parameter ......................................................... 332
Speed Detection
Parameter ......................................................... 332
Speed reference
LOCAL/REMOTE Run selection ............................. 296
Switching between LOCAL/REMOTE....................... 296
Stall Prevention function
Parameter ......................................................... 330