ABB ACSM1 - Page 290

Parameter data
290
16.03 PASS CODE INT32 0…2
31
-1 - 1 = 1 - 32 0 140
16.04 PARAM RESTORE enum 0…2 - 1 = 1 - 16 0 WPD 140
16.07 PARAM SAVE enum 0…1 - 1 = 1 - 16 0 140
16.09 USER SET SEL enum 1…10 - 1 = 1 - 32 1 WPD 141
16.10 USER SET LOG Pb 0…0x7FF - 1 = 1 - 32 0 WP 141
16.11 USER IO SET LO Bit pointer - - 32 C.False 142
16.12 USER IO SET HI Bit pointer - - 32 C.False 142
16.13 TIME SOURCE PRIO enum 0…8 - 1 = 1 - 16 0 142
16.20 DRIVE BOOT enum 0…1 - 1 = 1 - 32 0 WPD 142
17 PANEL DISPLAY
17.01 SIGNAL1 PARAM INT32 00.00…
255.255
- 1 = 1 - 16 01.03 143
17.02 SIGNAL2 PARAM INT32 00.00…
255.255
- 1 = 1 - 16 01.04 143
17.03 SIGNAL3 PARAM INT32 00.00…
255.255
- 1 = 1 - 16 01.06 143
17.04 SIGNAL1 MODE INT32 -1…3 - 1 = 1 - 16 0 143
17.05 SIGNAL2 MODE INT32 1…3 - 1 = 1 - 16 0 143
17.06 SIGNAL3 MODE INT32 1…3 - 1 = 1 - 16 0 144
20 LIMITS
20.01 MAXIMUM SPEED REAL 0…30000 rpm 1 = 1 2 ms 32 1500 145
20.02 MINIMUM SPEED REAL -30000…0 rpm 1 = 1 2 ms 32 -1500 145
20.03 POS SPEED ENA Bit pointer - 2 ms 32 C.True 146
20.04 NEG SPEED ENA Bit pointer - 2 ms 32 C.True 146
20.05 MAXIMUM CURRENT REAL 0…30000 A 1 = 100 10 ms 32
×
[
99.06]
146
20.06 MAXIMUM TORQUE REAL 0…1600 % 1 = 10 2 ms 16 300 146
20.07 MINIMUM TORQUE REAL -1600…0 % 1 = 10 2 ms 16 -300 146
20.08 THERM CURR LIM enum 0…1 - 1 = 1 - 16 1 147
22 SPEED FEEDBACK
22.01 SPEED FB SEL enum 0…2 - 1 = 1 10 ms 16 0 WPD 149
22.02 SPEED ACT FTIME REAL 0…10000 ms 1 = 1000 10 ms 32 3 149
22.03 MOTOR GEAR MUL INT32 -2
31
…2
31
-1 - 1 = 1 10 ms 32 1 150
22.04 MOTOR GEAR DIV UINT32 1…2
31
-1 - 1 = 1 10 ms 32 1 150
22.05 ZERO SPEED LIMIT REAL 0…30000 rpm 1 = 1000 2 ms 32 30 150
22.06 ZERO SPEED DELAY UINT32 0…30000 ms 1 = 1 2 ms 16 0 151
22.07 ABOVE SPEED LIM REAL 0…30000 rpm 1 = 1 2 ms 16 0 151
22.08 SPEED TRIPMARGIN REAL 0…10000 rpm 1 = 10 2 ms 32 500 152
22.09 SPEED FB FAULT enum 0…2 - 1 = 1 10 ms 16 0 152
22.10 SPD SUPERV EST REAL 0…30000 rpm 1 = 1 250 µs 32 450 153
22.11 SPD SUPERV ENC REAL 0…30000 rpm 1 = 1 250 µs 32 15 153
22.12 SPD SUPERV FILT REAL 0…10000 ms 1 = 1 250 µs 32 15 153
24 SPEED REF MOD
24.01 SPEED REF1 SEL enum 0…8 - 1 = 1 10 ms 16 1 155
24.02 SPEED REF2 SEL enum 0…8 - 1 = 1 10 ms 16 0 156
Index Parameter Type Range Unit FbEq Update
time
Data
length
Def PT Save
PF
Page
no.
22