ADCMT 6146 - Page 12

6146/6156 DC Voltage/Current Generators Operation Manual
Table of Contents
C-2
2.2.7 Continuous Function .................................................................................. 2-34
2.3 Program Mode ................................................................................................... 2-36
2.3.1 Memory Recall Mode ................................................................................. 2-36
2.3.1.1 Memory Setting .......................................................................................... 2-36
2.3.1.1.1 Entering Memory Data ............................................................................... 2-36
2.3.1.1.2 Saving Memory Data to Nonvolatile Memory ........................................... 2-39
2.3.1.1.3 Loading Data in Nonvolatile Memory to Volatile Memory ....................... 2-40
2.3.1.1.4 Initializing Memory Data in Volatile Memory .......................................... 2-41
2.3.1.2 Scan Mode .................................................................................................. 2-41
2.3.1.2.1 Executing Hold Scan .................................................................................. 2-42
2.3.1.2.2 Executing Single Scan ................................................................................ 2-44
2.3.1.2.3 Executing Repeat Scan ............................................................................... 2-45
2.3.2 Sweep Source Mode ................................................................................... 2-46
2.3.2.1 Setting Sweep Conditions ........................................................................... 2-46
2.3.2.2 Sweep Mode ............................................................................................... 2-48
2.3.2.2.1 Executing Hold Sweep ............................................................................... 2-49
2.3.2.2.2 Executing Single Sweep ............................................................................. 2-51
2.3.2.2.3 Executing Repeat Sweep ............................................................................ 2-53
2.4 Thermal Electromotive Force Output ............................................................... 2-55
2.4.1 Thermal Electromotive Force Output Operation ........................................ 2-55
2.4.2 Room Temperature Compensation ............................................................. 2-58
2.5 Saving and Loading Parameters ........................................................................ 2-59
2.5.1 Auto Load at Power ON ............................................................................. 2-59
2.5.2 Saving Parameters ...................................................................................... 2-60
2.5.3 Loading Parameters .................................................................................... 2-60
2.6 Panel Lock ......................................................................................................... 2-62
3. REFERENCE ................................................................................................ 3-1
3.1 Menu Index ....................................................................................................... 3-1
3.2 Function Description ......................................................................................... 3-2
3.2.1 DATA key (Direct Data Input Mode) ........................................................ 3-2
3.2.2 DOWN Key (Source Range Down) ........................................................... 3-2
3.2.3 LIMIT Key (Voltage and Current Limiter Setting) .................................... 3-2
3.2.4 MEM Key (Memory Setting) ..................................................................... 3-2
3.2.5 MENU Key (Parameter Setting) ................................................................ 3-2
3.2.6 OPR/SUSPEND Key (Operate/Suspend) ................................................... 3-9
3.2.7 POLARITY+ Key (Source Value Polarity and Zero) ................................ 3-9
3.2.8 POLARITY 0 Key (Source Value Polarity and Zero) ............................... 3-9
3.2.9 POLARITY- Key (Source Value Polarity and Zero) ................................. 3-9
3.2.10 PRGM MODE Key
(Switching to and Releasing Memory Recall/Sweep Source) .................... 3-9
3.2.11 SCAN MODE Key (Selecting Scan Mode) ............................................... 3-10
3.2.12 SHIFT/LOCAL Key (Shift Mode/Local) ................................................... 3-11
3.2.13 STBY Key (Output Standby) ..................................................................... 3-11
3.2.14 STEP TIME/SEL Key ................................................................................ 3-12
3.2.15 TRIG HOLD Key (Trigger and Hold for Memory Recall/Sweep Source) 3-12
3.2.16 UNIT Key (Continuous Key UP) ............................................................... 3-13
3.2.17 UNIT Key (Continuous Key Down) .......................................................... 3-13
3.2.18 UP Key (Increasing Source Range) ............................................................ 3-13