AOR AR-Mini User Manual (English)

Other manuals for AOR AR-Mini

Questions and Answers:

K
Kevin MooreAug 20, 2025
What to do if my AOR Receiver has no power?
- J
  jmurphyAug 20, 2025
  If your AOR Receiver isn't powering on, there are several possible causes: * The battery may be completely drained, in which case you should replace it with a new one. * The battery might need charging, so ensure it is properly charged. * The battery polarity might be incorrect; make sure you've inserted the battery with the correct orientation. * You might not be pressing the power (PWR) key long enough. Press and hold the PWR key for at least 2 seconds.
S
Sarah BowmanAug 22, 2025
Why is there no audio coming from my AOR Receiver?
- R
  Richard RodriguezAug 22, 2025
  If you're experiencing no audio from your AOR Receiver, here are a few things to check: * Ensure the volume isn't set too low; increase it to a comfortable level. * Make sure you've correctly tuned to the desired frequency. * Verify that the reception mode is properly configured. * The squelch value might be set too high. Set the squelch to “Threshold.” * The tone squelch frequency could be incorrect. Set the tone squelch correctly. * The DCS code might be wrong. Set the code correctly.
A
Alyssa HannaAug 25, 2025
How to fix no reception on AOR AR-Mini Receiver?
- K
  Kelly AguirreAug 25, 2025
  If your AOR Receiver isn't picking up any signals, consider the following: * Ensure the antenna is correctly and securely attached. * Verify that you have tuned to the correct frequency. * Confirm that you've selected the appropriate antenna type using setting number 17 or 18. * Check if the attenuator function is enabled and, if so, disable it.
D
Dustin WilliamsonAug 27, 2025
What to do if the audio is distorted on my AOR AR-Mini?
- J
  Janet GarciaAug 27, 2025
  If the audio from your AOR Receiver sounds distorted, it might be due to: * An incorrectly tuned frequency. Make sure you correctly tune the frequency. * An incorrect reception mode. Adjust the reception mode to the appropriate setting.
S
Sandra CobbAug 28, 2025
Why is my AOR Receiver emitting noise?
- J
  Julia BarkerAug 28, 2025
  If your AOR Receiver is emitting noise, the squelch value might be set too low. Set the squelch to “Threshold.”
L
lloydbrittanyAug 30, 2025
What to do if the search is not started on AOR Receiver?
- R
  Richard FlowersAug 30, 2025
  If the search function on your AOR Receiver isn't starting, it might be because the squelch value is set too small. Set the squelch to “Threshold.”
S
Sharon PerezSep 1, 2025
What to do if the scan is not started on AOR AR-Mini Receiver?
- L
  Luke BoyleSep 1, 2025
  If the scan function on your AOR Receiver isn't starting, it might be because the squelch value is set too small. Set the squelch to “Threshold.”
S
Sandra EllisonSep 3, 2025
Why is my AOR Receiver skipping a specific frequency?
- M
  Mary LiuSep 3, 2025
  If your AOR Receiver is skipping a specific frequency during a search, it's possible that the search skip function is enabled. Cancel the search skip to include that frequency in your scans.
D
Deborah CampbellSep 5, 2025
How to unlock keys on AOR AR-Mini Receiver?
- D
  Douglas BlackburnSep 5, 2025
  If the keys on your AOR Receiver are not responding, the key lock function may be activated. To restore key functionality, cancel the key lock function.
R
Raymond EdwardsSep 7, 2025
Why is there no audio from my AOR Receiver?
- J
  Jose DuncanSep 7, 2025
  If you're not getting any audio from your AOR Receiver, here are a few things to check: First, make sure the volume isn't set too low; increase it. Verify that you've tuned to the correct frequency. Ensure the reception mode is correctly set. Also, the squelch value might be set too high; adjust it to “Threshold.” Finally, check that the tone squelch frequency and DCS code are correctly set.

AOR AR-Mini Specifications

General

Brand	AOR
Model	AR-Mini
Category	Receiver
Language	English

Summary

FCC Warning

For Safety

Icon Labels Explained

Explains the meaning of various warning and prohibition icons used in the manual.

General Electrical and Fire Safety

Precautions against electrical hazards, fire risks, and improper handling of the equipment.

For Safety - Battery and Adapter

Battery and AC Adapter Safety

Detailed safety guidelines for handling batteries, AC adapters, and cords.

Important Safety Notes

Crucial advice on plug handling, cleaning, charging, and battery maintenance.

Introduction to AR-mini

Packing List

Lists all items included in the product packaging for user verification.

About the AR-mini Receiver

Introduces the AR-mini receiver's capabilities and basic design.

AR-mini Operating Modes

Explains the different operating modes: VFO, Memory, Preset, and Setting.

Part Names and Functions

Identifies and describes the physical parts and buttons of the AR-mini.

Key Functions Explained

Detailed explanation of the functions of each key on the AR-mini device.

Component Details

Details on dial knob, earphone jack, battery case, MONI, FUNC, and antenna connectors.

LCD Display Indicators

Explains the various segments and symbols displayed on the AR-mini's LCD screen.

Preparation and Basic Usage

Connecting the Antenna

Step-by-step guide on how to attach and detach the provided antenna.

Attaching Belt Clip and Hand Strap

Instructions for attaching the belt clip and tying the hand strap for portability.

Installing Batteries

Guide on inserting Ni-MH or AA batteries into the AR-mini.

Charging the Ni-MH Battery

Steps for charging the supplied Ni-MH batteries using the AC adapter.

Charging Tips and Notes

Additional tips and information regarding the battery charging process.

Optional Accessories and DC Adapter

Lists optional accessories and explains using the DC-mini DC adapter.

Cloning and PC Programming

Instructions for data cloning via CO-mini cable and PC programming via PC-mini cable.

Connecting PC-mini for Programming

Steps for connecting the PC-mini to the computer and AR-mini for programming.

Running the PC-mini Programming Software

How to launch and use the AR-mini programming software on a PC.

Basic Operation of AR-mini

Switching On and Off

How to power the AR-mini on and off.

Adjusting Volume and Squelch

Guide on using the dial knob to adjust receiver volume and squelch levels.

Adjusting the Frequency

Guide to tuning the receiver to different frequencies and bands.

Adjusting the Squelch Level

Instructions for setting the squelch level to minimize background noise.

Changing Reception Mode and Monitoring

How to select reception modes and use the monitoring function.

Changing AR-mini Operating Mode

Explains how to switch between VFO, Memory, and Preset modes.

Advanced Operation Features

Priority Watch Function

How to set up and use the priority watch feature for monitoring specific frequencies.

2VFO Watch Operation

Instructions for using the dual VFO watch function to monitor two frequencies.

2VFO Watch with Memory and Customization

Using stored memories to start 2VFO watch and how to update them.

VFO Search and Frequency Skipping

How to perform automatic frequency search and skip specific frequencies.

Limit Search Functionality

How to set a specific frequency range for searches.

Search Types and Band Memory

Explains search modes and managing search band memory.

Limit Link Search Operation

How to link multiple limit search ranges together.

Memory Mode and Limit Search Example

Overview of memory mode and an example of linked limit search.

Storing and Recalling Memory Channels

Step-by-step guides for saving and accessing stored frequencies.

Returning to VFO and Erasing Memory

How to exit memory mode and delete individual memory channels.

Erasing All Memory in a Bank

How to delete all stored frequencies from a specific memory bank.

Memory Naming and Scanning

How to name memory channels and initiate a scan through them.

Skipping Memory in Scan and Bank Scanning

How to mark memories to skip and scan specific memory banks.

Scanning Linked Memory Banks

How to scan multiple linked memory banks sequentially.

Broadcast and Preset Mode Usage

How to use pre-programmed broadcast radio frequencies and preset channels.

Tone Squelch and Frequency Search

How to set tone squelch and search for tone frequencies.

Reversed Tone Squelch and DCS Operation

Using reversed tone squelch and setting Digital Code Squelch (DCS).

Secret Comm., Attenuator, and Key Lock

Receiving secret comms, using the attenuator, and activating key lock.

Wiretap Frequency Search and Detector

How to search for wiretap frequencies and use the detector function.

System and Full Content Reset

How to perform system reset and reset all contents to factory defaults.

Setting Mode Configurations

Frequency Step Settings

How to adjust the frequency tuning step size and fast step increment.

Lamp and Timer Settings

How to configure LCD backlight duration and set auto power-off/alarm timers.

S-meter Sensitivity Adjustment

Adjusting the sensitivity of the S-meter for optimal performance.

S-meter Buzzer and Resume Time

Configuring S-meter beeps and setting resume time for scans.

Setting Search Methods

How to select between VFO Search, Limit Search, and Limit Link Search.

Setting Memory Scan Options

How to configure memory scan methods like All, Bank Link, and Bank.

Setting Limit Link Search

How to link memory banks for sequential scanning operations.

Setting Memory for Bank Link Scan

How to configure memory banks for linked scanning operations.

Confirming Limit Search Frequencies and Erasing Bank Memory

Checking limit search frequencies and erasing all memory from a bank.

Erasing VFO Skip Memory

How to delete frequencies marked to be skipped during VFO searches.

Erasing Memory Skip Mark and Canceling Scan Muting

Removing skip marks from memory channels and disabling scan muting.

Antenna Settings: Built-in Bar and Earphone

How to select the built-in bar antenna or use an earphone as an antenna.

Automatic Volume in FM and Tone Frequency

Enabling automatic volume increase in FM and setting tone frequencies.

Reversed Tone and Scrambled Carrier Frequencies

Selecting reversed tone frequencies and carrier frequencies for scrambled comms.

Automatic Display Switching and DCS Code

Automatic display changes and setting Digital Code Squelch (DCS) codes.

DCS Code Phases and Beep Control

Setting DCS code phases and disabling device beeps.

Battery Saving and Voltage Display

Adjusting battery saving timers and displaying battery voltage.

Ni-MH Battery Charging Settings

Specific settings and procedures for charging the Ni-MH battery.

Step Frequency Revision and Clock Shift

Revising step frequencies and shifting the microprocessor's clock rate.

Appendix and Reference Information

Broadcast Radio Mode Frequencies

Lists frequencies for broadcast radio mode for US and European versions.

Preset Memory Frequencies

Lists frequencies for preset memory channels for US and European versions.

Short-wave Broadcast Station List

A detailed list of short-wave broadcast stations with frequencies.

Tone Frequency and DCS Code Lists

Lists of available tone frequencies and DCS codes for squelch functions.

Search Band and 2VFO Watch Memory Lists

Lists of defined frequency ranges for search bands and 2VFO watch memories.

Setting Mode List (Parts 1-3)

Index of setting modes, their initial displays, functions, and page numbers.

Troubleshooting Common Issues

Common problems and their solutions for the AR-mini receiver.

Technical Specifications

Detailed technical specifications of the AR-mini receiver, including frequency range, power, etc.

AR-Mini Notes and FAQs

Volume/Squelch in Broadcast/Preset Modes

How to adjust volume/squelch in Broadcast Facility and Preset modes.

External Antenna Reception Issues

Explains why external antennas may not improve AM/SW reception.

Importance of Antenna Selection

Highlights the importance of correct antenna selection for sensitivity and measurements.

Related product manuals

AOR AR-Mini User Manual

Table of Contents