Bosch B4512 - Points Menu Parameters

Control Panels Keypad Installer menu | en 113
Bosch Security Systems, Inc. Installation Manual 2018.07 | 16 | F.01U.287.180
5. Delete existing characters, if necessary, and then enter the new characters.
6. Press Save or Enter. The keypad shows Parameter saved.
7. Escape from the menu.
User (Passcode) Worksheet (Includes users added only through RPS, the Installer Services
Portal programming tool (available in Europe, Middle East, Africa, and China), or the Main
menu)
User ### Passcode User
group
Area authority
1 ￚￚￚￚ 2 ￚￚￚￚ 3* ￚￚￚￚ 4*
User name
000 123 __ __ __ ____ 15 15 15 15 SERVICE PASSCODE
001 123456 ____ 1 __ __ __ USER 1
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
* Applicable to B5512 only.
20.1.16 [7] Points menu parameters
Use the parameters in this menu to assign a Point Source and a Point Profile to each point.
The Point Source parameter assigns the point to a device (on-board, Octo-input, and wireless
are examples). The Point Profile determines how the point operates.