2-2 2007 Buell P3: Chassis
HOME
TORQUE VALUES
ITEM TORQUE NOTES
Brake bleeder valve 36-60
in-lbs
4-7 Nm Metric, Page 2-23
Brake line to master cylinder banjo bolts 16-20 ft-lbs 22-27 Nm Page 2-27
Clutch lever screw 40-48
in-lbs
4.6-5.4 Nm Page 2-72
Footpeg support mounting bracket bolts 25-30 ft-lbs 34-41 Nm Page 2-61
Frame-to-isolator rear fastener 30-33 ft-lbs 41-45 Nm
Apply several drops of Loctite Thread-
locker 271 (red) to last few threads, Page
2-74
Front and rear brake rotor screws, TORX 24-27 ft-lbs 33-37 Nm
Tighten in criss-cross pattern. Apply sev-
eral drops of Loctite Threadlocker 271
(red) to last few threads, Page 2-13
Front axle nut 38-42 ft-lbs 52-57 Nm
Apply several drops of Loctite 243 (blue)
to last few threads. Metric, Page 2-11
Front axle pinch screw 13-16 ft-lbs 18-22 Nm Metric, Page 2-11
Front brake caliper mounting bolts 18-22 ft-bs 24-30 Nm
Apply several drops of Loctite Thread-
locker 271 (red) to last few threads, Page
2-30
Front brake caliper pad hanger pin 11-15 ft-lbs 15-20 Nm Metric, Page 2-30
Front brake hand lever nut 44-62
in-lbs
5-7 Nm Metric, Page 2-26
Front brake line clamp screw 36-60
in-lbs
4-7 Nm Page 2-32
Front brake switch screw 7-13
in-lbs
0.8-1.5 Nm Page 2-26
Front fender mounting screws 27-30
in-lbs
3.1-3.4 Nm Page 2-63
Front isolator mount bolt 63-70 ft-lbs 85-95 Nm Page 2-73
Front muffler bolts 17-19 ft-lbs 24-25 Nm Page 2-59
Front sprocket cover bolts 30-36
in-lbs
3-4 Nm Page 2-62
Front tie bar bolt 30-33 ft-lbs 41-45 Nm Page 2-73
Handlebar clamp fasteners 120-144
in-lbs
14-16 Nm Page 2-72
Handlebar left and right housing screws 25-33
in-lbs
3-4 Nm Page 2-72
Instrument panel screws 30-36
in-lbs
3-4 Nm
Apply several drops of Loctite 243 (blue)
to last few threads, metric, Page 2-69
Lower and upper header nuts 72-96
in-lbs
8-11 Nm Lower first, Page 2-59
Lower belt guard 30-36
in-lbs
3-4 Nm Page 2-65
Master cylinder cover screws 9-13
in-lbs
1.0-1.5 Nm Page 2-31
Outboard isolator bolts 30-33 ft-lbs 41-45 Nm Page 2-73
Rear axle nut 49-51 ft-lbs 67-69 Nm Page 2-14, 2-58
Rear brake caliper mounting screw, large 18-22 ft-lbs 24-30 Nm Metric, Page 2-40
Rear brake caliper mounting screw, small 14.5-18 ft-lbs 20-24 Nm Metric, Page 2-40
Rear brake caliper pad hanger pin 132-180
in-lbs
15-20 Nm Metric, Page 2-39
Rear brake fastener 72-96
in-lbs
8-11 Nm Page 2-62
Rear brake reservoir mounting screw 12-15
in-lbs
1.4-1.7 Nm Page 2-36
To Next Page
Loading...
