Seat Reversal Sets the various options for wheelchairs that have a reversing seat
Charger Inhibit 3 Enable Dedicates the Inhibit 3 input on the Power Module to operate with an On -Board Charger
Charger Inhibit 3 Latching Sets whether the OBC inhibit (PM Inhibit 3) as described above is latching or non-latching
Charger Inhibit 1 Latching Sets whether Inhibit 1 (JSM Charger Socket) is latching or non-latching
Charger Inhibit 1 Alarm Sets whether an alarm sounds if there is an inhibit present on the JSM Charger Socket
Charger Inhibit 3 Alarm Sets whether an alarm sounds if there is an inhibit present on the PM Inbibit 3
Front Wheel Drive
Front Wheel Drive Type Sets specific specialist software to support Front Wheel Drive Wheelchairs
Front Wheel Drive Selects specialist software for front wheel driven wheelchairs
FWD Acceleration Sets the limit of forward acceleration when exiting a turn
Advanced Electronic Stability (AES)
Advanced Electronic Stability Sets whether the specialist stability software is turned on
AES Rate Sets the rate of adjustment of Advanced Electronic Stability
Motor
Global
Maximum Current Limit Sets the long term maximum current output of the Power Module
Boost Drive Current Sets the short term maximum current output of the Power Module
Boost Drive Time Sets the period of time that the level of current set by Boost Drive Current is available
Current Foldback Threshold Sets the level of current which, if exceeded, will start the current foldback timer
Current Foldback Time Sets the period of time that the current must exceed the above parameter before the current is reduced
Current Foldback Level Sets the level of current output reduction
Compensation Matches the PM to the motors
Invert M1 Direction Inverts the direction of rotation of motor channel M1 on the Power Module
Invert M2 Direction Inverts the direction of rotation of motor channel M2 on the Power Module
Motor Swap Swaps the motor output channels, M1 and M2, of the Power Module
*Steer Correct Adjusts the PM outputs to compensate for mis-matched motors
*Display Speed Sets whether the speed and odometer is displayed in miles per hour or kilometers per hour
Displays Sets the format of the digital speed display to be Speed, Odometer or Both
Maximum Rated Speed This calibrates the speedometer function
*Maximum Displayed Speed This sets the operation of the graphical speed display
Joystick Stationary Time Sets the period of time that the joystick must be deflected before drive is removed
Joystick Stationary Range Sets the ‘window’ within which the joystick is considered to be stationary
Profiled
Compensation Factor Allows different values of Compensation to be used across different profiles.
Inhibits
Global
Disable Inhibit 2 in Drive Sets whether the PM Inhibit 2 input is interrogated constantly or just at entry into Drive Mode
Disable Inhibit 3 in Drive Sets whether the PM Inhibit 3 input is interrogated constantly or just at entry into Drive Mode
Disable Inhibit 8 in Drive For parameter information - Refer to the Specialist Chapter – ASM/TM
Disable Inhibit 9 in Drive For parameter information - Refer to the Specialist Chapter – ASM/TM
Inputs - PM
Lower Level Threshold Sets the threshold between Band 0 and Band 1 for a particular Inhibit Input on the PM
Middle Level Threshold Sets the threshold between Band 1 and Band 2 for a particular Inhibit Input on the PM
Upper Level Threshold Sets the threshold between Band 2 and Band 3 for a particular Inhibit Input on the PM
Debounce Time Sets a debounce time for the inhibit input.
Inputs - ISM
Lower Level Threshold Sets the threshold between Band 0 and Band 1 for a particular Inhibit Input on the ISM
Middle Level Threshold Sets the threshold between Band 1 and Band 2 for a particular Inhibit Input on the ISM
Upper Level Threshold Sets the threshold between Band 2 and Band 3 for a particular Inhibit Input on the ISM
Debounce Time Sets a debounce time for the inhibit input
Inputs – ISM8/CxSM
Lower Level Threshold For parameter information - Refer to the Chapter – ISM8
Middle Level Threshold For parameter information - Refer to the Chapter – ISM8
Upper Level Threshold For parameter information - Refer to the Chapter – ISM8
Debounce Time For parameter information - Refer to the Chapter – ISM8
To Next Page
Loading...
Need help?
General
