Table of Contents
Service Instructions 869-M PREMIUM - 00.0 - 07/2018 3
18.3.6 Assembling the handwheel flange............................................ 89
18.3.7 Assembling the handwheel....................................................... 90
19 Programming .......................................................................... 91
19.1 Calling up the Technician level................................................. 91
19.2 Structure of the software........................................................... 91
19.3 Lock technician level (Lock Techn.) submenu...................... 92
19.4 ParameterCall submenu...................................................... 92
19.5 Default Program submenu.................................................. 94
19.5.1 Setting the Stitch length (Stitchlen.) parameter ................. 94
19.5.2 Setting the Foot pressure (Foot Press.) parameter............. 95
19.5.3 Setting the Needle thread tension (Thr.Tens.) parameter .......95
19.5.4 Setting the Sewing foot stroke (Foot Stroke) parameter...... 95
19.5.5 Setting the Start bartack (Start Tack) parameter................. 96
19.5.6 Setting the End bartack (End Tack) parameter ...................... 96
19.5.7 Setting the Thread cutter (Thread Trim) parameter.............. 96
19.5.8 Setting the Daily pieces counter (DailyPieces) parameter......96
19.6 Machine config. submenu.................................................. 97
19.6.1 Setting the Thread cutter (Thread Trim) parameter.............. 98
19.6.2 Setting the Thread clamp (Thread Clamp) parameter........... 99
19.6.3 Setting the Speed (Speed) parameter.................................... 101
19.6.4 Setting the Stop positions (Stop Positions) parameter ...... 101
19.6.5 Setting the Sewing foot (Foot) parameter ............................. 102
19.6.6 Setting the Needle thread tension (Thr.Tens.) parameter .... 102
19.6.7 Setting the Sewing foot stroke (Stroke) parameter .............. 103
19.6.8 Setting the Stitch length (Stitchlen.) parameter ............... 104
19.6.9 Setting the Bobbin (Bobbin) parameter................................. 104
19.6.10 Setting the Motor holding force (Holding Force)
parameter ............................................................................... 105
19.6.11 Setting the Pedal (Pedal) parameter..................................... 106
19.6.12 Setting the Needle cooling (NeedleCooling) parameter ....... 106
19.6.13 Setting the Seam center guide (Center Guide) parameter... 107
19.6.14 Setting the Puller (Puller) parameter................................... 107
19.6.15 Setting the Edge guide (EdgeGuide) parameter ................... 109
19.6.16 Setting the Material thickness detection
(FabricThickness) parameter............................................ 109
19.6.17 Setting the Correction of effects of high speed
(Speed Corr.) parameter .................................................... 11
0
19.6.18 Setting the Light barrier (LightBarrier) parameter............ 110
19.6.19 Setting the Segment length (Mode Seg.Size) parameter ..... 111
19.6.20 Setting the Threading mode (Threading) parameter ........... 111
19.6.21 Setting the Operation lock (MachineBlockage) parameter ... 111
19.7 User config. submenu ...................................................... 111
19.7.1 Setting the Language selection (Language) parameter ........ 112
19.7.2 Setting the Parameter View (ParameterView) parameter ... 112
19.7.3 Setting the Input configuration (Input Config) parameter ... 113
19.7.4 Setting the Output configuration (Output Config)
parameter ............................................................................... 115
19.7.5 Setting the Additional inputs/outputs (Add I/O) parameter..... 116
19.7.6 Setting the barcode scanner (Scanner) parameter............... 119
19.7.7 Setting the Interface (Interface) parameter ....................... 119
19.7.8 Setting the Stitch functions (StitchFunctions) parameter..... 119
To Next Page
Loading...
Need help?
General
