Epson Stylus Pro 4400 - Page 484

EPSON Stylus Pro 4400/4450/4800/4880/4880C Revision C
Appendix Parts List 484
728 “COMPRESSION SPRING,0.52”
729 “GROUND PLATE,B;B”
730 “LEVER,INCLINATION”
731 “EXTENSION SPRING,3.81”
732 “CARRIAGE,A;B”
734 “PLATE,BEARING,L,C593”
735 “LEVER,CAM,C593”
736 “STOPPER,CARRIAGE”
737 “SHAFT,INCLINATION CAM”
738 “HARNESS,HEAD,A”
739 “HARNESS,HEAD,C”
740 “SHEET,FFC”
741 “SOLENOID ASSY.,CR,C593,ESL,ASP”
742 “ADJUST PLATE,CR,UPPER”
743 “ADJUST PLATE,CR,LOWER”
744 “C.P.P-TITE SCREW,2.6X8,F/ZN-3C”
745 “SPACER,CARREAGE A”
746 BALL BEARING(B210151490)
747 “HARNESS,HEAD,B”
750 “EXTENSION SPRING,11.4”
751 “EXTENSION SPRING,2.55”
752 “LEVER,LOCK,PG”
753 “BUSHING,LOCK;B”
756 “EXTENSION SPRING,2.58”
757 “LEVER,SCALE,CR”
758 “EXTENSION SPRING,3.86”
759 “SCALE,CR”
760 “BELT,CR”
761 “PULLEY,DRIVEN”
762 “SHAFT,PULLEY”
763 “COMPRESSION SPRING,29.4”
770 “DETECTOR,HP;E”
772 “BELT,PG”
773 “HARNESS,DETECTOR,PG”
774 “DETECTOR,HP;E”
Table 7-9. Stylus Pro 4400
Figure Part Name
778 “BOARD ASSY.,ENCODER”
779 “HOLDER,TUBE,B,C593”
780 “PAD,TUBE”
781 “HOLDER,TUBE,A,C593”
782 “BOARD ASSY.,SUB”
783 “HARNESS,ENCODER”
784 “COVER,TUBE,C593”
785 “GUIDE,TUBE,CR,C593”
786 “SHEET,TUBE”
787 “GUIDE PLATE,TUBE”
788 “SHEET,SUS”
789 “HOLDER,FFC,C593”
790-A “SPACER,MIDDLE,0.05”
790-B “SPACER,MIDDLE,0.1”
790-C “SPACER,MIDDLE,0.2”
790-D “SPACER,MIDDLE,0.5”
790-E “SPACER,MIDDLE,0.08”
791 “HARNESS,DETECTOR,HP”
792 BALL BEARING(B210151490)
800 “DETECTOR,LEAF,B2”
801 “HARNESS,PAPER EJECT PHASE,LEFT”
802 “LEVER,CHANGE PAPER EJECT,L”
803 “EXTENSION SPRING,6.99”
805 “MOUNT PLATE,MOTOR,ASF ASSY.,C593”
806 “COMBINATION GEAR,12,22.4”
807 “SPUR GEAR,25.6”
808 “COMBINATION GEAR,12.8,36”
809 “COMBINATION GEAR,13.6,28.8”
810 “SPUR GEAR,20”
811A “PG TRANSMIT ASSY.,C593”
814 “HOLDER,PLANET,RELEASE;B”
815 “SPUR GEAR,16,RELEASE”
816 “SPUR GEAR,22,RELEASE”
817 “POLY SLIDER,STW-FT70,t=0.25”
818 “COMPRESSION SPRING,0.98”
Table 7-9. Stylus Pro 4400
Figure Part Name