Epson Stylus Pro 4400 - Adjustment Items Classified by Part;Unit; Required Adjustment Items;Execution Order

EPSON Stylus Pro 4400/4450/4800/4880/4880C Revision C
Adjustment Overview 368
5.1.4 Adjustment Items classified by Part/Unit
Required adjustment items and execution order for each part/unit that has
been replaced or removed is shown in the table below.
Note "*1": RP = Replacement with new part
"*2": RM = Removal only
Table 5-2. Required Adjustment Items/Execution Order
Name Adjustment Item RP
*1
RM
*2
Ref.
Main Circuit Board
<common to Stylus
Pro 4400/4450/
4800/4880/4880C>
(Backup = O.K.)
1 Parameter Backup { --- P.409
2 RTC&USB ID&IEEE1394ID
{ --- P.387
Main Board
<Stylus Pro 4800/
4880/4880C>
(Backup = NG)
1 Device ID setting
(Stylus 4450/4880/4880C only)
{ --- P.446
2 Initial Ink Charge Flag ON/OFF { --- P.408
3 RTC&USB ID&IEEE1394ID { --- P.387
4 Head Rank ID { --- P.388
5 Rear Sensor AD Adjustment { --- P.407
6 Check Nozzle { --- P.436
7 Check Alignment { --- P.437
8 1000mm Feed Adjustment { --- P.407
9 Nozzle Bi-D Adjustment { --- P.393
10 Printhead Slant Adjustment (PF) { --- P.394
11 PG Adjustment { --- P.383
12 Nozzle Bi-D Adjustment { --- P.393
13 Printhead Slant Adjustment (PF) { --- P.394
14 Printhead Slant Adjustment (CR) { --- P.397
15 Multi Sensor Level Adjustment { --- P.389
16 T&B&S (Roll Paper) { --- P.390
17 T&B&S (Cut Sheet) { --- P.391
18 Platen Position Adjustment { --- P.405
19 Multi Sensor Adjustment for Auto
Nozzle Check
{ --- P.402
20 Auto Uni-d Adjustment { --- P.401
Main Board
<Stylus Pro 4800/
4880/4880C>
(Backup = NG)
21 Auto Bi-d Adjustment { --- P.430
21 Manual Bi-D { --- P.431
22 Image Adjustment { --- P.439
23 Cutter Pressure Adjustment { --- P.392
24 Writing MAC Address { --- P.447
Main Board
<Stylus Pro 4400/
4450>
(Backup = NG)
1 Erasing Firmware { --- P.445
2 Installing Firmware { --- P.445
3 Selecting “4-colors” { --- P.445
4 Device ID setting
(Stylus 4450/4880/4880C only)
{ --- P.446
5 Initial Ink Charge Flag ON/OFF { --- P.408
6 RTC&USB ID&IEEE1394ID { --- P.387
7 Check Alignment { --- P.437
8 1000mm Feed Adjustment { --- P.407
9 Nozzle Bi-D Adjustment { --- P.393
10 Printhead Slant Adjustment (PF) { --- P.394
11 PG Adjustment { --- P.383
12 Nozzle Bi-D Adjustment { --- P.393
13 Printhead Slant Adjustment (PF) { --- P.394
14 Printhead Slant Adjustment (CR) { --- P.397
15 Multi Sensor Level Adjustment { --- P.389
16 T&B&S (Roll Paper) { --- P.390
17 T&B&S (Cut Sheet) { --- P.391
18 Platen Position Adjustment { ---
P.405
19 Multi Sensor Adjustment for Auto
Nozzle Check
{ --- P.402
20 Auto Uni-d Adjustment { --- P.401
21 Auto Bi-d Adjustment { --- P.430
22 Manual Bi-D { --- P.431
23 Image Adjustment { --- P.439
24 Cutter Pressure Adjustment { --- P.392
25 Writing MAC Address { --- P.447
Table 5-2. Required Adjustment Items/Execution Order
Name Adjustment Item RP
*1
RM
*2
Ref.