Index
S
Security............................................................. 4
Security Code ................................................. 42
Security Code ................................................. 97
Segment Time Remaining In Hours ............. 188
Set Point Select Function Key........................ 99
Set Up Group.................................................. 37
Set Up Wiring Procedure For Auxiliary Output
.................................................................. 146
Setpoint Code Selections.............................. 189
Setpoint High Limit........................................ 74
Setpoint Low Limit ........................................ 74
Setpoint Ramp ................................................ 44
Setpoint Ramp .............................................. 123
Setpoint Ramp Final Setpoint......................... 45
Setpoint Ramp Time....................................... 44
Setpoint Ramp/Soak Programming .......... 4, 125
Setpoint Rate .................................................. 45
Setpoint Rate ............................................ 4, 123
Setpoint Tracking ........................................... 73
Setpoints ........................................... 4, 106, 189
Shed Time ......................................................85
Test Failures ................................................. 156
TX Delay ........................................................85
Wiring Connections For Calibrating Auxiliary
Output.......................................................146
Slowtune...........................................................5
Soak Segments .............................................127
Software Type .............................................. 188
Software Upgrade Part Number ................... 172
Software Upgrades ....................................... 171
Software Version.......................................... 188
Software Version Number............................155
Solid State Relay Output ................................ 29
Solid State Relays........................................... 13
SP Ramp Set Up Group.................................. 44
SP Tuning....................................................... 48
Specifications ................................................. 12
Start Segment Number .................................126
Start Up Procedure For Operation................ 104
Status Tests................................................... 156
Stray Rejection ............................................... 12
Summer With Ratio And Bias........................ 54
Suppression Devices ......................................21
Switch Between Two Sets Via Keyboard ....118
Switching Between Setpoints....................... 107
T
Temperature Units.......................................... 92
Thermocouple Health ....................................... 2
Thermocouple Inputs Using A Thermocouple
Source.......................................................137
Thermocouple Inputs Using An Ice Bath..... 136
Three Position Control Step Output Start-Up
Mode........................................................... 74
Three Position Step ........................................ 52
Three Position Step Control ......................... 148
Three Position Step Control Algorithm........120
Three Position Step Control Connections ......32
Three Position Step Test Failures.................156
Time Current Duplex......................................61
Time Duplex...................................................61
Time Proportional Output...............................60
Time Proportional Output Failure ................163
Time Remaining ...........................................108
Time Simplex .................................................60
Time-Out ......................................................109
Timer ........................................................4, 108
Timer ..............................................................52
Transmitter Characterization ....................65, 69
Transmitter Power ............................................3
Transmitter Power For 4-20 Ma ...............34, 35
Troubleshooting Aids ...................................154
Troubleshooting Procedures.........................160
Troubleshooting/Service...............................153
Tune..............................................................110
Tune For Duplex (Heat/Cool) ......................111
Tuning ............................................................40
Tuning Constants..............................................4
Tuning Indicators .........................................109
Tuning Parameter Sets....................................71
Tuning Set Up Group .....................................40
Two Sets Of Tuning Constants.....................116
U
Universal Output Functionality And Restrictions
..............................................................22, 23
Universal Switching Power ..............................4
V
Voltage And Resistance Equivalents For 0%
And 100% Range Values..........................133
W,X,Y,Z
Weight ............................................................14
Weighted Average Ratio ................................56
Wiring.............................................................20
Wiring Bundling.............................................21
Wiring Connections For Calibrating Current
Proportional Output..................................144
Wiring Connections For Radiamatic,
Milliampere, Millivolts, Or Volts
(Except 0 To 10 Volts) .....................138, 139
Wiring Connections For Rtd (Resistance
Thermometer Device)...............................137
Wiring Diagrams ............................................22
Wiring The Controller ....................................24
Worksheet.....................................................125
WS Float.........................................................85
226 UDC3200 Universal Digital Controller Product Manual 12/04
To Next Page
Loading...
