HP ProCurve 5400zl User Manual

■ well-defined < af11 | af12 | af13 | ... > -- Define mapping between a DSCP
(Differentiated-Services Codepoint) value and an 802 (p. 434)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ ipv6 -- specify the ipv6 address of the device to set the priority (IPV6-ADDR) (p. 425)
■ dscp -- Specify DSCP policy to use. (p. 418)
■ binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY) (p. 416)
■ integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal. (p. 423)
■ well-defined < af11 | af12 | af13 | ... > -- Define mapping between a DSCP
(Differentiated-Services Codepoint) value and an 802 (p. 434)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ ipv6/mask -- specify the ipv6 address with prefix-length of the device to set the priority
(IPV6-ADDR/PREFIX-LEN) (p. 425)
■ dscp -- Specify DSCP policy to use. (p. 418)
■ binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY) (p. 416)
■ integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal. (p. 423)
■ well-defined < af11 | af12 | af13 | ... > -- Define mapping between a DSCP
(Differentiated-Services Codepoint) value and an 802 (p. 434)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ [no] qos dscp-map -- Define mapping between a DSCP (Differentiated-Services Codepoint) value
and an 802 (p. 421)
■ binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY) (p. 416)
■ name -- Specify DSCP->priority mapping name. (p. 426)
■ name-string -- Specify DSCP->priority mapping name. (ASCII-STR) (p. 426)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal. (p. 423)
■ name -- Specify DSCP->priority mapping name. (p. 426)
■ name-string -- Specify DSCP->priority mapping name. (ASCII-STR) (p. 426)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ well-defined < af11 | af12 | af13 | ... > -- Define mapping between a DSCP (Differentiated-Services
Codepoint) value and an 802 (p. 434)
■ name -- Specify DSCP->priority mapping name. (p. 426)
■ name-string -- Specify DSCP->priority mapping name. (ASCII-STR) (p. 426)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ [no] qos protocol < IP | IPX | ARP | ... > -- Configure protocol-based priority (p. 431)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ qos queue-config -- Sets the number of outbound port queues that buffer the packets depending
on their 802 (p. 432)
■ 2-queues -- Set the number of outbound port queues for all switch ports. (p. 415)
■ 4-queues -- Set the number of outbound port queues for all switch ports. (p. 415)
■ 8-queues -- Set the number of outbound port queues for all switch ports. (p. 415)
■ [no] qos type-of-service -- Configure the Type-of-Service method the device uses to prioritize IP
traffic (p. 433)
■ diff-services -- In IP Differentiated Services (Diffserv) mode, IPv4 packets are classified and
given a QoS priority based on the upper 6 bits of the IP ToS field from the packets as they enter
the switch. The assignment of Diffserv Codepoints to 802.1p priorities is done via the qos
dscp-map command. Any Diffserv Codepoint in an inbound IPv4 packet can be re-mapped to
a different codepoint (and its associated 802.1p priority) on outbound. This is done by using
the syntax: qos type-of-service diff-services <af11..ef|0-63|000000...111111> dscp
<af11..ef|0-63|000000...111111> (p. 418)
■ binary-codepoint < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY) (p. 416)
■ dscp -- Define Differentiated Services Codepoint to which to map IP ToS. (p. 418)
■ binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY) (p. 416)
■ integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal. (p. 423)
413© 2009 Hewlett-Packard Development Company, L.P.
qosCommand Line Interface Reference Guide

HP ProCurve 5400zl Specifications

General

Brand	HP
Model	ProCurve 5400zl
Category	Switch
Language	English