HP ProCurve 5400zl

■ well-defined < af11 | af12 | af13 | ... > -- Define mapping between a DSCP
(Differentiated-Services Codepoint) value and an 802 (p. 434)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ ipv6 -- Specify range of TCP/UDP ports from [to] which to prioritize traffic. (p. 425)
■ port-num -- TCP/UDP port from [to] which to prioritize traffic. (TCP/UDP-PORT) (p. 427)
■ dscp < 000000 | 000001 | 000010 | ... > -- Specify DSCP policy to use. (p. 418)
■ binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY) (p. 416)
■ integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal. (p. 423)
■ well-defined < af11 | af12 | af13 | ... > -- Define mapping between a DSCP
(Differentiated-Services Codepoint) value and an 802 (p. 434)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ range -- Specify range of TCP/UDP ports from [to] which to prioritize traffic. (p. 432)
■ port-num -- TCP/UDP port from [to] which to prioritize traffic. (TCP/UDP-PORT) (p. 427)
■ max-port-num -- Maximal TCP/UDP port in the range from [to] which to prioritize
traffic. (TCP/UDP-PORT) (p. 425)
■ dscp < 000000 | 000001 | 000010 | ... > -- Specify DSCP policy to use. (p. 418)
■ binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY)
(p. 416)
■ integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal. (p. 423)
■ well-defined < af11 | af12 | af13 | ... > -- Define mapping between a DSCP
(Differentiated-Services Codepoint) value and an 802 (p. 434)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ port-num -- TCP/UDP port from [to] which to prioritize traffic. (TCP/UDP-PORT) (p. 427)
■ dscp < 000000 | 000001 | 000010 | ... > -- Specify DSCP policy to use. (p. 418)
■ binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY) (p. 416)
■ integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal. (p. 423)
■ well-defined < af11 | af12 | af13 | ... > -- Define mapping between a DSCP
(Differentiated-Services Codepoint) value and an 802 (p. 434)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ range -- Specify range of TCP/UDP ports from [to] which to prioritize traffic. (p. 432)
■ port-num -- TCP/UDP port from [to] which to prioritize traffic. (TCP/UDP-PORT) (p. 427)
■ max-port-num -- Maximal TCP/UDP port in the range from [to] which to prioritize traffic.
(TCP/UDP-PORT) (p. 425)
■ dscp < 000000 | 000001 | 000010 | ... > -- Specify DSCP policy to use. (p. 418)
■ binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY) (p.
416)
■ integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal. (p. 423)
■ well-defined < af11 | af12 | af13 | ... > -- Define mapping between a DSCP
(Differentiated-Services Codepoint) value and an 802 (p. 434)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ [no] qos device-priority -- Configure device-based priority (p. 417)
■ ip-addr -- specify the ipv4 address of the device to set the priority (IP-ADDR) (p. 424)
■ dscp -- Specify DSCP policy to use. (p. 418)
■ binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY) (p. 416)
■ integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal. (p. 423)
■ well-defined < af11 | af12 | af13 | ... > -- Define mapping between a DSCP
(Differentiated-Services Codepoint) value and an 802 (p. 434)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 428)
■ ipv4/mask -- specify the ipv4 address with subnet mask of the device to set the priority
(IP-ADDR/mask-LENGTH) (p. 425)
■ dscp -- Specify DSCP policy to use. (p. 418)
■ binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY) (p. 416)
■ integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal. (p. 423)
412© 2009 Hewlett-Packard Development Company, L.P.
qosCommand Line Interface Reference Guide