EasyManua.ls Logo

Huawei quidway s7700 - Page 61

Huawei quidway s7700
833 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Step 2 Configure the basic MPLS capability, set up the LDP peers, and enable MPLS TE, Resource
Reservation Protocol-TE (RSVP-TE), and Constraint Shortest Path First (CSPF).
# In this example, RSVP-TE is used as the signaling protocol. Enable global MPLS TE and
RSVP-TE on the PEs and P along the TE tunnel. Configure CSPF on the tunnel ingress. Enable
MPLS TE and RSVP-TE on the interfaces along the tunnel. Configure the LDP remote peers
on PEs to transmit the private network routes.
# Configure PE1.
[PE1] mpls lsr-id 1.1.1.9
[PE1] mpls
[PE1-mpls] mpls te
[PE1-mpls] mpls rsvp-te
[PE1-mpls] mpls te cspf
[PE1-mpls] quit
[PE1] interface vlanif 7
[PE1-Vlanif7] mpls
[PE1-Vlanif7] mpls te
[PE1-Vlanif7] mpls rsvp-te
[PE1-Vlanif7] quit
[PE1] mpls ldp
[PE1-mpls-ldp] quit
[PE1] mpls ldp remote-peer 2.2.2.9
[PE1-mpls-ldp-remote-2.2.2.9] remote-ip 2.2.2.9
[PE1-mpls-ldp-remote-2.2.2.9] quit
[PE1] mpls ldp remote-peer 3.3.3.9
[PE1-mpls-ldp-remote-3.3.3.9] remote-ip 3.3.3.9
[PE1-mpls-ldp-remote-3.3.3.9] quit
# The configuration procedures of PE2 and PE3 are similar to the configuration procedure of
PE1.
# Configure the P.
[P] mpls lsr-id 4.4.4.9
[P] mpls
[P-mpls] mpls te
[P-mpls] mpls rsvp-te
[P-mpls] quit
[P] interface vlanif 7
[P-Vlanif7] mpls
[P-Vlanif7] mpls te
[P-Vlanif7] mpls rsvp-te
[P-Vlanif7] quit
[P] interface vlanif 5
[P-Vlanif5] mpls
[P-Vlanif5] mpls te
[P-Vlanif5] mpls rsvp-te
[P-Vlanif5] quit
[P] interface vlanif 6
[P-Vlanif6] mpls
[P-Vlanif6] mpls te
[P-Vlanif6] mpls rsvp-te
[P-Vlanif6] quit
# Run the display mpls ldp session command on the PEs, and you can see that LDP peers are
set up between PE1 and PE2 and between PE1 and PE3.
# Take the display on PE1 as an example:
[PE1] display mpls ldp session
LDP Session(s) in Public Network
Codes: LAM(Label Advertisement Mode), SsnAge Unit(DDDD:HH:MM)
A '*' before a session means the session is being deleted.
------------------------------------------------------------------------------
Quidway S7700 Smart Routing Switch
Configuration Guide - VPN 1 VPN Tunnel Management Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
46

Table of Contents

Other manuals for Huawei quidway s7700

Related product manuals