<S-PE> display ip routing-table
Route Flags: R - relied, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 18 Routes : 18
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.9/32 OSPF 10 3 D 20.1.1.1 Vlanif30
2.2.2.9/32 OSPF 10 2 D 20.1.1.1 Vlanif30
3.3.3.9/32 Direct 0 0 D 127.0.0.1 InLoopBack0
4.4.4.9/32 OSPF 10 2 D 30.1.1.2 Vlanif40
5.5.5.9/32 OSPF 10 3 D 30.1.1.2 Vlanif40
10.1.1.0/24 OSPF 10 2 D 20.1.1.1 Vlanif30
20.1.1.0/24 Direct 0 0 D 20.1.1.2 Vlanif30
20.1.1.2/32 Direct 0 0 D 127.0.0.1 InLoopBack0
20.1.1.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
30.1.1.0/24 Direct 0 0 D 30.1.1.1 Vlanif40
30.1.1.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
30.1.1.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
40.1.1.0/24 OSPF 10 2 D 30.1.1.2 Vlanif40
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
The U-PEs can ping each other. Take the display on U-PE1 for example.
<U-PE1> ping 40.1.1.2
PING 40.1.1.2: 56 data bytes, press CTRL_C to break
Reply from 40.1.1.2: bytes=56 Sequence=1 ttl=252 time=160 ms
Reply from 40.1.1.2: bytes=56 Sequence=2 ttl=252 time=120 ms
Reply from 40.1.1.2: bytes=56 Sequence=3 ttl=252 time=150 ms
Reply from 40.1.1.2: bytes=56 Sequence=4 ttl=252 time=150 ms
Reply from 40.1.1.2: bytes=56 Sequence=5 ttl=252 time=160 ms
--- 40.1.1.2 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 120/148/160 ms
Step 3 Enable MPLS and set up LSPs and LDP sessions.
Configure the basic MPLS capability on the MPLS backbone network. Set up tunnels and LDP
sessions between U-PE1 and S-PE, and between S-PE and U-PE2.
# Configure U-PE1.
[U-PE1] mpls lsr-id 1.1.1.9
[U-PE1] mpls
[U-PE1-mpls] quit
[U-PE1] mpls ldp
[U-PE1-mpls-ldp] quit
[U-PE1] interface vlanif 20
[U-PE1-Vlanif20] mpls
[U-PE1-Vlanif20] mpls ldp
[U-PE1-Vlanif20] quit
[U-PE1] mpls ldp remote-peer 3.3.3.9
[U-PE1-mpls-ldp-remote-3.3.3.9] remote-ip 3.3.3.9
[U-PE1-mpls-ldp-remote-3.3.3.9] quit
# Configure P1.
[P1] mpls lsr-id 2.2.2.9
[P1] mpls
[P1-mpls] quit
[P1] mpls ldp
Quidway S7700 Smart Routing Switch
Configuration Guide - VPN 6 PWE3 Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
604
To Next Page
Loading...
