[PE1-Tunnel2/0/0] mpls te commit
[PE1-Tunnel2/0/0] quit
# Configure PE2.
[PE2] interface tunnel 1/0/0
[PE2-Tunnel1/0/0] ip address unnumbered interface loopback 1
[PE2-Tunnel1/0/0] tunnel-protocol mpls te
[PE2-Tunnel1/0/0] destination 1.1.1.9
[PE2-Tunnel1/0/0] mpls te tunnel-id 100
[PE2-Tunnel1/0/0] mpls te signal-protocol rsvp-te
[PE2-Tunnel1/0/0] mpls te commit
[PE2-Tunnel1/0/0] quit
# Configure PE3.
[PE3] interface tunnel 1/0/0
[PE3-Tunnel1/0/0] ip address unnumbered interface loopback 1
[PE3-Tunnel1/0/0] tunnel-protocol mpls te
[PE3-Tunnel1/0/0] destination 1.1.1.9
[PE3-Tunnel1/0/0] mpls te tunnel-id 100
[PE3-Tunnel1/0/0] mpls te signal-protocol rsvp-te
[PE3-Tunnel1/0/0] mpls te commit
[PE3-Tunnel1/0/0] quit
# Run the display this interface command in the tunnel interface view of the PEs, and you can
see that the TE tunnel is Up. Take Tunnel1/0/0 of PE1 for example.
[PE1-Tunnel1/0/0] display this interface
Tunnel1/0/0 current state : UP
Line protocol current state : UP
Last line protocol up time : 2007-09-10 13:54:57-08:00
Description:HUAWEI, Quidway Series, Tunnel1/0/0 Interface
Route Port,
Internet Address is unnumbered, using address of LoopBack1(1.1.1.9/32)
Encapsulation is TUNNEL, loopback not set
Tunnel destination 2.2.2.9
Tunnel up/down statistics 1
Tunnel protocol/transport MPLS/MPLS, ILM is available,
primary tunnel id is 0x1003c, secondary tunnel id is 0x0
QoS max-bandwidth : 64 Kbps
Output queue : (Urgent queue : Size/Length/Discards) 0/50/0
Output queue : (Protocol queue : Size/Length/Discards) 0/1000/0
Output queue : (FIFO queue : Size/Length/Discards) 0/256/0
300 seconds output rate 0 bits/sec, 0 packets/sec
196 seconds output rate 0 bits/sec, 0 packets/sec
0 packets output, 0 bytes
0 output error
0 output drop
Input bandwidth utilization : --
Output bandwidth utilization : --
Step 6 Configure the VPN tunnel binding.
# Configure PE1. Bind PE1 to Tunnel1.
[PE1] mpls l2vpn
[PE1-l2vpn] mpls l2vpn default martini
[PE1-l2vpn] quit
[PE1] interface tunnel 1/0/0
[PE1-Tunnel1/0/0] mpls te reserved-for-binding
[PE1-Tunnel1/0/0] mpls te commit
[PE1-Tunnel1/0/0] quit
[PE1] tunnel-policy policy1
[PE1-tunnel-policy-policy1] tunnel binding destination 2.2.2.9 te tunnel 1/0/0
[PE1-tunnel-policy-policy1] quit
[PE1] interface VLANIF 10
Quidway S7700 Smart Routing Switch
Configuration Guide - VPN 1 VPN Tunnel Management Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
48
To Next Page
Loading...
