Korg Karma - Page 43

PROG
1.1
2.12.22.33.14.14.25.15.25.36.16.26.36.47.17.27.3
33
Asgn (GE real-time Parameter Assign)
[---, ...Dyn4]
Here you can assign the controller for the GE parameter.
By assigning GE parameters to KARMA real-time CON-
TROLS, they can be controlled in real-time while you play.
---: No assignment.
... (Knob 1...8): Assigns the parameter to KARMA
real-time CONTROLS knobs [1]–[8]. The knob will continu-
ously control the “value.”
For example, let’s assume that the “Rhythm Swing%”
parameter of the selected GE has a Value range of +0000–
+0100.
• If you set “Value”: +0050, “Asgn (Assign)”: Knob 1, and
[Pol (Polarity)]:+
Knob 1 at the center position (12 o’clock) will produce a
value of +0050. At far left the value will be +0000, and at
far right the value will be +0100. Turning the knob from
center toward the left will control the value from
+0050...+0000, and turning it from center toward the
right will control the value from +0050...+0100.
• If you set “Value”: +0080, “Asgn (Assign)”: Knob1, and
”Pol (Polarity)”:+
Knob 1 at the center position (12 o’clock) will produce a
value of +0080. At far left the value will be +0000, and at
far right the value will be +0100. Turning the knob from
center toward the left will control the value from
+0080...+0000, and turning it from center toward the
right will control the value from +0080...+0100.
... (Knob 1...8SW): Assign the parameter to
KARMA real-time CONTROLS knobs [1]–[8]. The knob will
switch the value between minimum and maximum only, in
a key (on/off) operation. The left range of the knob is off,
and the center and right is on.
• If you set “Value”: +0050, “Asgn (Assign)”: Knob 1SW,
and [Pol (Polarity)]:+
Turning the knob toward the left will produce a value of
+0000. Turning it to center or right will produce a value
of +0100.
... : The parameter will be assigned to switch [1]/[2].
The “Value” will be controlled between the minimum and
maximum values.
The maximum and minimum values controlled by
Knob1–8SW and SW1/2 will depend on the “Value”
setting.
[Example]
GE parameter Value range: in the case of 0...100
“Value” setting: +0050
Minimum value controlled by Knob1–8SW, SW1/2: 0
Maximum value controlled by Knob1–8SW, SW1/2: 100
“Value” setting: +0025
Minimum value controlled by Knob1–8SW, SW1/2: 0
Maximum value controlled by Knob1–8SW, SW1/2: 50
“Value” setting: +0075
Minimum value controlled by Knob1–8SW, SW1/2: 50
Maximum value controlled by Knob1–8SW, SW1/2: 100
The correspondence between the KARMA real-time
CONTROLS and MIDI control change messages can be
specified in Global mode 6.1–2. In this case, a MIDI con-
trol change message value of less than 64 will be “off,”
and 64 or greater will be “on.”
Dyn 1...4: This corresponds to Dynamic MIDI 1...4.
Select this if you wish to control a GE parameter using the
controller selected for “Source” in Dynamic MIDI (6.4–3a/
b/c/d). (Set the Dynamic MIDI (6.4–3a/b/c/d) “Destina-
tion” to RTParm Ctrl.)
Pol (GE real-time Parameter Polarity) [+, –]
Specifies the polarity used when you operate the KARMA
real-time CONTROLS that you selected for “Asgn.”
+: In the case of Knob1...8, rotating to the left of center will
lower the “Value,” and rotating to the right will raise it.
In the case of Knob1...8SW, the left side will be off, and
the center and right side will be on.
In the case of SW1/2, the parameter will be on when the
LED is lit.
–: In the case of Knob1...8, rotating to the left of center will
raise the “Value,” and rotating to the right will lower it.
In the case of Knob1...8SW, the left side will be on, and
the center and right side will be off.
In the case of SW1/2, the parameter will be on when the
LED is dark.
■ 6.3–1(2)(3)(4)b: UTILITY
☞ “Write Program” (1.1–1c), “Copy KARMA Module,” “Init
KARMA Module” (6.1–1c), “Select by Category” (1.1–3d)