Lenze i55AE155F

Parameterisaon required
1.
Set the operang mode "MS: Torque mode [-1]" in 0x6060 (P301.00).
2.
Set the rated motor torque in 0x6076 (P325.00).
3.
Set the permissible maximum torque in 0x6072 (P326.00).
•
The seng is made in percent with reference to the rated motor torque set in 0x6076
(P325.00).
4.
Select the source for the posive torque limit in 0x2949:001 (P337.01).
•
Default seng: Maximum torque 0x6072 (P326.00)
•
In case of selecon "Analog Input 1 [2]": Set seng range in 0x2636:011 (P430.11) and
0x2636:012 (P430.12).
•
In case of selecon "Analog Input 2 [3]": Set seng range in 0x2637:011 (P431.11) and
0x2637:012 (P431.12).
•
In case of selecon "Posive torque limit [4]": Set the posive torque limit in 0x60E0.
5.
Select the source for the negave torque limit in 0x2949:002 (P337.02).
•
Default seng: (-) Maximum torque 0x6072 (P326.00)
•
In case of selecon "Analog Input 1 [2]": Set seng range in 0x2636:011 (P430.11) and
0x2636:012 (P430.12).
•
In case of selecon "Analog Input 2 [3]": Set seng range in 0x2637:011 (P431.11) and
0x2637:012 (P431.12).
•
In case of selecon "Negave torque limit [4]": Set the negave torque limit in 0x60E1.
6.
Select the source for the upper speed limit in 0x2946:003 (P340.03).
•
Default seng: Maximum frequency 0x2916 (P211.00)
•
In case of selecon "Analog input 1 [2]": Set seng range in 0x2636:002 (P430.02) and
0x2636:003 (P430.03).
•
In case of selecon "Analog input 2 [3]": Set seng range in 0x2637:002 (P431.02) and
0x2637:003 (P431.03).
•
In case of selecon "Upper frequency limit [4]": Set the upper speed limit in [Hz] in
0x2946:005 (P340.05).
•
In case of selecon "Upper speed limit [5]": Set the upper speed limit in [vel. unit in
0x2946:001 (P340.01).
7.
Select the source for the lower speed limit in 0x2946:004 (P340.04).
•
Default seng: (-) Maximum frequency 0x2916 (P211.00)
•
In case of selecon "Analog input 1 [2]": Set seng range in 0x2636:002 (P430.02) and
0x2636:003 (P430.03).
•
In case of selecon "Analog input 2 [3]": Set seng range in 0x2637:002 (P431.02) and
0x2637:003 (P431.03).
•
In case of selecon "Lower frequency limit [4]": Set the lower speed limit in [Hz] in
0x2946:006 (P340.06).
•
In case of selecon "Lower speed limit [5]": Set the lower speed limit in [vel. unit in
0x2946:002 (P340.02).
8.
Select the standard setpoint source for the torque control in 0x2860:003 (P201.03).
•
Default seng: Analog input 1. In case of this selecon, set the seng range in
0x2636:011 (P430.11) and 0x2636:012 (P430.12).
•
In case of selecon "Analog input 2 [3]": Set seng range in 0x2637:011 (P431.11) and
0x2637:012 (P431.12).
•
Except for the network, the torque setpoint must be given in percent with regard to the
0x6076 (P325.00) rated motor torque.
•
Via the network the torque setpoint is selected via the mappable parameter 0x400B:
008 (P592.08) in [Nm / 2
scaling factor
]. The scaling factor can be set in 0x400B:009
(P592.09).
9.
Oponally: For a "smooth" change-over between dierent setpoint sources, adapt the
ramp me for the torque setpoint in 0x2948:002 (P336.02).
The torque control with frequency limitaon is now acve and the inverter responds to the
torque setpoint given by the selected setpoint source.
Motor control
Opmisaon of the control loops
Motor controller sengs
207