Lenze i55AE155F - Page 696

Address Designaon Default seng Category Data type Factor A M
0x4022:008
(P451.08)
PID setpoint presets: Preset 8 0.00 PID unit general I16 100 P -
0x4023:001
(P610.01)
PID sleep mode: Acvaon Disabled [0] general U8 1 P -
0x4023:002
(P610.02)
PID sleep mode: Stop method Coasng [0] general U8 1 P -
0x4023:003
(P610.03)
PID sleep mode: Frequency threshold 0.0 Hz general U16 10 P -
0x4023:004
(P610.04)
PID sleep mode: Feedback threshold 0.00 PID unit general I16 100 P -
0x4023:005
(P610.05)
PID sleep mode: Delay me 0.0 s general U16 10 P -
0x4023:006
(P610.06)
PID sleep mode: Recovery Setpoint > threshold OR
system deviaon > band-
width [0]
general U8 1 P -
0x4023:007
(P610.07)
PID sleep mode: Bandwidth 0.00 PID unit general U16 100 P -
0x4023:008
(P610.08)
PID sleep mode: Recovery threshold 0.00 PID unit general I16 100 P -
0x4024:001
(P615.01)
Automac rinsing: Rinsing in idle state Inhibited [0] general U8 1 P -
0x4024:002
(P615.02)
Automac rinsing: Rinse interval 30.0 min general U16 10 P -
0x4024:003
(P615.03)
Automac rinsing: Rinse speed 0.0 Hz general I16 10 P -
0x4024:004
(P615.04)
Automac rinsing: Rinse period 0.0 s general U16 10 P -
0x4025
(P800.00)
Sequencer mode Disabled [0] general U8 1 P -
0x4026:001
(P801.01)
Sequencer segment 1: Frequency setpoint 0.0 Hz general I16 10 P -
0x4026:002
(P801.02)
Sequencer segment 1: Acceleraon/deceleraon 5.0 s general U16 10 P -
0x4026:003
(P801.03)
Sequencer segment 1: Time 0.0 s general U32 10 P -
0x4026:004
(P801.04)
Sequencer segment 1: Digital outputs 0 general U8 1 P -
0x4026:005
(P801.05)
Sequencer segment 1: Analog outputs 0.00 VDC general U16 100 P -
0x4026:006
(P801.06)
Sequencer segment 1: PID setpoint 0.00 PID unit general I16 100 P -
0x4026:007
(P801.07)
Sequencer segment 1: Torque setpoint 100.0 % general I16 10 P -
0x4026:008 Sequencer segment 1: NetWordOUT2 0 general U16 1 P -
0x4026:009 Sequencer segment 1: Reserved 0 general U32 1 P -
0x4027:001
(P802.01)
Sequencer segment 2: Frequency setpoint 0.0 Hz general I16 10 P -
0x4027:002
(P802.02)
Sequencer segment 2: Acceleraon/deceleraon 5.0 s general U16 10 P -
0x4027:003
(P802.03)
Sequencer segment 2: Time 0.0 s general U32 10 P -
0x4027:004
(P802.04)
Sequencer segment 2: Digital outputs 0 general U8 1 P -
0x4027:005
(P802.05)
Sequencer segment 2: Analog outputs 0.00 VDC general U16 100 P -
0x4027:006
(P802.06)
Sequencer segment 2: PID setpoint 0.00 PID unit general I16 100 P -
0x4027:007
(P802.07)
Sequencer segment 2: Torque setpoint 100.0 % general I16 10 P -
* Default seng depending on the size. Firmware version 05.00.00.00
Appendix
Parameter aribute list
696