Microplex SOLID F44 - How to Start the Self Test

Configuring the Printer
3-3
--- Self Test ---
MENU
TEAR OFF FORM PAPER MENU PCL-MENU *)
SELECT PROFILE = 1 PAPER = CUTOM FONT NUMBER = 0
FEED N PAGES = 3 PAPER LENGTH = 12 INCH PITCH = 10.00 **)
SELECT FOLD LENGTH FACTOR = 1 SYMBOL SET = ROMAN-8
CHANGE PROFILE IMAGE WIDTH = 8,25 INCH LINE SPACING = LINES/INCH
BASIC SETTINGS ORIENTATION = PORTRAIT TOP MARGIN = 0 LINES
TEST MODE LANDSCAPE MODE = REVERSE LEFT MARGIN = 0 COLUMNS
RESET PRINTER = NO ORIENT. MODUE = FIXED RIGHT MARGIN = MAXIMUM
PAPER EXTENDED = NO TEXT LENGTH = 72 LINES
PAPERSELECTION = ONLY PJL PERF. SKIP = OFF
FUSIER TEMP. = MIDDLE $$ COMMANDS = OFF
HUMIDITY = NORMAL
TONER DENSITY = MIDDLE
VER SHIFT = 0/100 INCH
HOR SCHIFT = 0/100 INCH
INIT LINE REG. = 4
GENERAL MENU CONFIG MENU CLOCK MENU
EMULATION = PCL *) POWER SAVE = 15 MIN WEEKDAY = MONDAY
AUTO FORM FEED = OFF ALARM BELL = ON DAY = 1
AUTO TEAT OFF = 30 SEC LANGUAGE = ENGLISH MONTH = AUGUST
TEAR OFF TIME = 10 SEC MENU ACCESS = ALL YEAR = 2011
TEAR OFF SHIFT = 0/24 INCH HOST CHANEL = PARALLEL HOUR = 13
PAPER RETRACT = ON RECAL FACTORY = NO MINUTE = 31
RESET TRU INFO = NO SECOND = 45
EXCHANGE TRU = NO
TEST MENU INFO MENU
PANELTEST PRINTER TYPE
= F44
Data Memory(DRAM) : 128 MB
SELF TEST ENGINE ID = 71XXXXXXXX-XX Bootstrap Version : X.XX
PRINT TEST FIRMWARE VERS. = 200XXXXXXX X.XX Emulations:
AUTO-TEST CONT CPC-FPGA VERS. = X.XX PCL
PCL-TYPE LIST STACKER VERS. = X.XX X.XX HEXDUMP
IC INFO = 15% USED
TRU INFO = 12% USED
FUSER INFO = 18% USED
MACHINE COUT = 900 PAGES
!"#$%´()*+,B./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}▒!"#$%´()*+,B./0123456789:;<=>?@ABCDEFGHIJKLMNOP
"#$%´()*+,B./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}▒!"#$%´()*+,B./0123456789:;<=>?@ABCDEFGHIJKLMNOP
#$%´()*+,B./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}▒!"#$%´()*+,B./0123456789:;<=>?@ABCDEFGHIJKLMNOPQ
3.2.1 How to Start the SELF TEST
Key Display
1. Switch the printer ON ONLINE (1) (after initialization)
2. Press [ONLINE] OFFLINE (1)
3. [MENU] key OFFLINE (1)
TEAR OFF FORM
4. Repeatedly pressing the OFFLINE (1)
Button to select TEST MODE
5. Press TEST MODE
TEST MENU
6. Press TEST MENU
PANELTEST
7. Repeatedly pressing the TEST MENU
Button to select SELF TEST
8. Press to activate TESTMENU
SELF TEST
The printer starts to print the SELF TEST. The printer returns to ONLINE after
pressing the [ONLINE] key.
*) Depending on setting of EMULATION in the GENERAL MENU either PCL-MENU or
HEXDUMP MENU is indicated.
**) This value is depending on the selected FONT NUMBER;
- for FONT NUMBER 0, and 39 up to 44 = PITCH
- for FONT NUMBER 1 up to 38 = POINT SIZE