NETGEAR XS708T User Manual

Configure Routing
208
XS708T, XS712Tv2, and XS716T Smart Managed Pro Switch User Manual
14. In the Adv NS Interval field, specify the retransmission time field of router advertisements
sent from the interface.
A value of 0 means the interval is not specified for the router. The range of the neighbor
solicit interval is 1000 to 4294967295. The default is 0.
15. In the Adv Reachable Interval field, specify the router advertisement time.
This is the time allocated to consider the neighbors reachable after ND confirmation. The
range of reachable time is 0 to 3600000. The default is 0.
16. Use the Adv Interval field to specify the maximum time allowed between sending router
advertisements from the interface.
The range of the maximum advertisement interval is 4 to 1800. The default value is 600.
17. From the Adv Managed Config Flag menu, specify the setting for the router advertisement
managed address configuration flag.
When the selection is Enable, end nodes use DHCPv6. When the selection is Disable,
end nodes autoconfigure addresses. The default value is Disable.
18. From the Adv Other Config Flag menu, select to enable or disable the router
advertisement other stateful configuration flag.
The default value is Disable.
19. From the Router Preference menu, specify the router preference advertisement on an
interface.
The default value is Medium.
20. From the Adv Suppress Flag menu, select to enable or disable the router advertisement
suppression on an interface.
The default value is Disable.
21. From the Destination Unreachables menu, select to enable or disable the mode for
sending ICMPv6 destination unreachable messages on this interface.
If this mode is disabled, the interface does not send ICMPv6 destination unreachable
messages. By default, the IPv6 destination unreachables mode is enabled.
22. Click the Apply button.
The updated configuration is sent to the switch. Configuration changes take effect
immediately.
The following table describes the nonconfigurable data that is displayed.
Table 57. IPv6 VLAN Configuration information
Field Description
Routing Mode Displays the routing mode of an interface. The default is Disable.

NETGEAR XS708T Specifications

General

Switch type	Managed
Switch layer	L2+/L3
Quality of Service (QoS) support	Yes
USB 2.0 ports quantity	1
SFP+ module slots quantity	2
Installed SFP modules quantity	-
Basic switching RJ-45 Ethernet ports type	10G Ethernet (100/1000/10000)
Basic switching RJ-45 Ethernet ports quantity	8
Certification	CE, FCC Cl. A, VCCI Cl. A, Cl. A EN 55022 (CISPR 22), Cl. A C-Tick, EN 55024, CCC
Product color	Black
LED indicators	Activity, Link, Power
Number of fans	1 fan(s)
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1ab, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3an, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Virtual LAN features	Private VLAN, Protocol-based VLAN
Cable types supported	Cat5e, Cat6, Cat6a, Cat7
Copper ethernet cabling technology	10GBASE-T
Noise level	29.1 dB
Flash memory	256 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276832 h
Jumbo frames	9000
Latency (10 Gbps)	3.012 µs
MAC address table	16000 entries
Packet buffer memory	2 MB
Number of static routes	32
DHCP features	DHCP server, DHCP client
Security algorithms	802.1x RADIUS
Access Control List (ACL) rules	100
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	96 W
Operating altitude	0 - 3000 m
Operating temperature (T-T)	0 - 50 °C
Operating relative humidity (H-H)	0 - 90 %
Cables included	AC

Weight and Dimensions

Depth	204 mm
Width	440 mm
Height	43 mm
Weight	2980 g