Name: Olympus RollerFORM
Brand: Olympus
Rating: 5 (1 reviews)

Default Chapter7

Figure I-1 Labels on the Rollerform7

Labels and Symbols7

Important Information - Please Read before Use11

Introduction21

1 Rollerform Scanner Overview23

Figure 1-1 the Contents of the Rollerform Case23

2 Setting up the Instrument35

3 Preparing the Rollerform Liquid Chamber45

4 Preparing for an Inspection55

5 Performing an Inspection69

6 Maintenance77

Removing the Acoustic Wheel from the Rollerform Scanner77
Figure 6-1 Removing the Probe Angle-Adjustment Components78
Figure 6-2 Removing the Acoustic Wheel's Holding Brackets79
Emptying the Acoustic Wheel's Liquid Chamber80
Figure 6-3 Removing the Acoustic Wheel80
Figure 6-4 the Location of the out Valve82
Changing the Probe-Axle83
- Removing the Probe from the Acoustic Wheel83
- Figure 6-5 Emptying the Liquid Chamber83
- Figure 6-6 Removing the Bushing from End of the Probe-Axle84
- Figure 6-7 Removing the External Retaining C-Clip from the End of the Probe-Axle85
- Installing the Probe in the Acoustic Wheel86
- Figure 6-8 Pushing the Probe-Axle out of the Acoustic Wheel86
- Figure 6-9 Inserting the Probe-Axle Inside the Acoustic Wheel87
- Figure 6-10 Installing the External Retaining C-Clip on the Probe-Axle End88
- Figure 6-11 Pushing the C-Clip in the Groove on the Probe-Axle End with the C-Clip Installation Tool89
- Figure 6-12 Pushing the C-Clip in the Groove on the Probe-Axle End with the C-Clip Installation Tool90
Cleaning the Liquid Chamber91
Figure 6-13 Probe Cable Extending from the Front to the Rear End of the Rollerform Handle91
Figure 6-14 Removing the Acoustic Wheel Flange's External Retaining Screws93
Figure 6-15 Removing the Acoustic Wheel Plain Flange94
Figure 6-16 Installing the Plain Flange95
Preserving or Restoring the Tire's Transparency96
- Preserving the Tire's Transparency96
- Figure 6-17 the Location of the out Valve97
- Restoring the Tire's Transparency98
- Figure 6-18 Emptying the Liquid Chamber98
- Figure 6-19 Removing the Plain Flange's External Retaining Screws99
- Figure 6-20 Removing the Acoustic Wheel Plain Flange100
- Figure 6-21 Installing the Plain Flange101
Changing the Tire102
Figure 6-22 Installing the Plain Flange's External Retaining Screws102
Figure 6-23 the Stainless Steel Rings that Hold the Flanges to the Tire103
Figure 6-24 Removing the Plain Flange's External Retaining Screws104
Figure 6-25 Removing the Acoustic Wheel Plain Flange105
Figure 6-26 Accessing the Captive Screws of the Flange with the Liquid-Control Valves from Inside the Liquid Chamber106
Figure 6-27 Pushing a Ring out of Its Retaining Groove107
Figure 6-28 Removing a Ring out of the Tire107
Figure 6-29 Inserting a Ring in the Tire108
Figure 6-30 Installing a Ring in Its Retaining Groove in the Tire109
Figure 6-31 Installing the Flange with the Liquid-Control Valves110
Figure 6-32 Tightening the Captive Screws of the Flange that Contains the Liquid-Control Valves from Inside the Liquid Chamber111
Figure 6-33 Installing the Plain Flange112
Installing the Acoustic Wheel on the Rollerform Scanner113
Figure 6-34 Installing the Plain Flange's External Retaining Screws113
Figure 6-35 Installing the Bushing on the End of the Probe-Axle114
Figure 6-36 Installing the Acoustic Wheel Holding Brackets115
Changing the Mini-Wheel Encoder116
Figure 6-37 Installing the Probe's Angle-Adjustment Components116
- Removing the Mini-Wheel Encoder from the Rear Roller117
- Figure 6-38 Cutting the Cable Tie off the Rollerform Handle117
- Figure 6-39 Removing the Screws from the Rollerform Handle118
- Figure 6-40 Loosening the Rear Roller's Retaining Screw119
- Figure 6-41 Pushing Loose the Rear Roller's Axle from Its Seat120
- Figure 6-42 Sliding out the Rear Roller's Axle121
- Figure 6-43 Loosening the Encoder Retaining Screw122
- Figure 6-44 Removing the Mini-Wheel Encoder123
- Removing the Mini-Wheel Encoder from the Alternate Encoder Holder124
- Figure 6-45 the Mini-Wheel Encoder Installed on the Alternate Encoder Holder124
- Figure 6-46 Removing and Pivoting the Alternate Encoder Holder 90125
- Figure 6-47 Tightening the Screw of the Alternate Encoder Holder126
- Installing the Mini-Wheel Encoder on the Rear Roller127
- Figure 6-48 Tightening the Encoder Retaining Screw128
- Figure 6-49 Aligning the Rear Roller's Axle-End Flat Bevel with the Retaining Screw129
- Figure 6-50 Installing the Handle Cap on the Rollerform's Handle130
Relocating the Mini-Wheel Encoder on the Acoustic Wheel131
Figure 6-51 Installing the Cable Sheath and the Cable Tie131
Figure 6-52 Loosening the Rear Roller's Retaining Screw132
Figure 6-53 Pushing Loose the Rear Roller's Axle from Its Seat133
Figure 6-54 Sliding out the Rear Roller's Axle134
Figure 6-55 Loosening the Encoder Retaining Screw135
Figure 6-56 Removing the Mini-Wheel Encoder136
Figure 6-57 Aligning the Rear Roller's Axle-End Flat Bevel with the Retaining Screw137
Figure 6-58 Loosening the Screw of the Alternate Encoder Holder138
Figure 6-59 Removing and Pivoting the Alternate Encoder Holder 90139
Figure 6-60 the Mini-Wheel Encoder Installed on the Alternate Encoder Holder140
6.10 Changing the Laser Batteries141
Figure 6-61 Changing the Batteries in the Laser141
6.11 Adjusting the Angle of the Guiding Laser Beam142
Figure 6-62 Aligning the Guiding Laser Beam143

7 Specifications145

8 Spare Parts149

Brand	Olympus
Model	RollerFORM
Category	Laboratory Equipment
Language	English

Olympus RollerFORM User Manual

Table of Contents

Questions and Answers:

Olympus RollerFORM Specifications

Related product manuals