Omron MX2 Series User Manual

Index
I - 4
Multi-function Compact Inverter 3G3MX2-EV2 User’s Manual (I666-E1)
P24S ..............................................................................2-15
Parameter initialization ........................................ 3-10, 3-27
Password Function.........................................................7-57
Permission of RUN Command .......................................7-38
Phase loss .....................................................................2-26
PID Feedback Value Monitor ........................................... 7-5
PID Function ..................................................................7-44
PIDC ............................................................................. 7-49
PLC ................................................................................2-15
Position Command Monitor ............................................7-12
Power interruption/Undervoltage ................................... 7-64
Power ON time over .......................................................7-85
Power Recovery Restart Prevention Function................7-68
Power supply .................................................................2-26
Pulse train frequency input .............................................7-52
Q
Query frame .....................................................................8-7
R
Radio noise ....................................................................2-33
Radio Noise Filter ................................................ 2-18, 12-3
Reactor ..........................................................................2-28
Real Frequency Monitor ...................................................7-7
Reduced torque characteristics ....................5-9, 5-15, 5-17
Reduced Voltage Startup Selection ............................... 7-36
REF ................................................................................7-91
Regenerative Braking Load Rate Monitor .......................7-16
Regenerative braking unit ................................... 2-18, 12-3
Regenerative braking unit connection terminal .............. 2-34
Remote Operation Function .......................................... 7-40
Returning Display to d001 ............................................. 3-10
Reverse run ...................................................................5-58
RNT................................................................................7-84
RUN ...............................................................................7-82
RUN Command ..............................................................5-21
RUN Command Status Signal ........................................7-91
RUN Direction Limit Selection ........................................7-38
RUN Direction Monitor .................................................... 7-5
RUN Time Over ..............................................................7-84
S
Safety Function ..............................................................7-99
Safety function STO input terminals ...............................2-10
SET ................................................................................7-33
SETM .............................................................................7-92
SFT ................................................................................7-54
Signal during RUN .........................................................7-82
Silent interval ...................................................................8-7
Sink logic ....................................................2-39, 2-40, 2-41
Soft Lock Function .........................................................7-54
Source logic ................................................2-39, 2-40, 2-42
Stabilization Parameter ................................................. 7-52
Start frequency ............................................................... 7-26
Start ratio ....................................................................... 7-26
Start selection ................................................................ 7-26
Starting contact signal.................................................... 7-88
Starting Frequency ......................................................... 7-35
Stopping motor .............................................................. 3-29
Surge absorber .............................................................. 2-26
T
Terminal block cover ........................................................2-9
Terminating resistor selector switch ............................... 2-10
TH .................................................................................. 7-82
Thermistor Trip Function ................................................ 7-82
Torque Bias Monitor ......................................................... 7-8
Torque boost function ..................................................... 5-59
Torque Reference Monitor ............................................... 7-7
Total Power ON Time Monitor ........................................ 7-10
Total RUN Time Monitor .................................................7-10
Transition of parameter display ........................................3-8
Transition of Parameter Display and Key Operation
in Extended Function Mode U ......................................3-9
Trip ................................................................................ 10-3
TRQ ............................................................................... 6-13
U
UDC ............................................................................... 7-40
UP .................................................................................. 7-40
Upper limit ..................................................................... 5-30
User Parameter Automatic Setting Function ......... 3-7, 7-60
User Parameter Setting Function ................................... 7-60
User setting ...................................................................... 5-4
USP ............................................................................... 7-68
UV .................................................................................. 7-65
W
WAC .............................................................................. 7-86
WAF ............................................................................... 7-87
Warning .......................................................................10-11
Warning Monitor ............................................................. 7-15
WCOI ............................................................................. 7-90
WCO .............................................................................. 7-90
Window Comparator ...................................................... 7-90

Omron MX2 Series Specifications

General

Cooling Method	Fan cooling
Output Frequency Range	0.1 to 400 Hz
Control Method	V/f control, Sensorless vector control
Protection Functions	Overcurrent, overvoltage, undervoltage, overload, overheating, short circuit
Communication Options	Modbus RTU
Overload Capacity	150% for 60 seconds
Braking Unit	Built-in
Ambient Operating Temperature	-10°C to +50°C
Enclosure	IP20
Storage Temperature	-20°C to +65°C
Humidity	5 to 95% RH (non-condensing)
Altitude	Up to 1000m
Power Supply Voltage	200-240V AC
Input Voltage	3-phase 200-240V AC