Why can't I set Step SV, step time, OUT1 proportional band, or EV alarm value on my Shinko Controller?
If you cannot set Step SV, step time, OUT1 proportional band, or EV alarm value, it's likely because a set value lock (Lock 1 or Lock 4) is selected. Release the lock in [Set value lock].
Why can I only set step SV, step time, and EV Alarm value on my Shinko PCB1?
If you can only set step SV, step time, and EV Alarm value, it means a set value lock (Lock 2 or Lock 5) is selected. Release the lock in [Set value lock].
General| Type | PCB1 |
|---|---|
| Category | Controller |
| Input Voltage | 24 VDC |
| Output Voltage | 5 VDC |
| Current Rating | 1 A |
| Operating Temperature | 0 to 50°C |
| Weight | 200 g |
| Manufacturer | Shinko |
Lists abbreviations for terms like PV, SV, MV used in the manual.
Provides important usage instructions, warnings, and disclaimers for the controller.
Covers warnings, cautions, and general safety advice for device operation.
Details environmental conditions and precautions for safe panel mounting.
Lists safety guidelines and best practices for electrical wiring.
Advises on safe operation, cleaning, and maintenance procedures.
Explains the model designation and its components.
Describes how to read and understand the information on the unit's model label.
Explains the function of each display segment and indicator light on the controller.
Details the purpose and operation of each button on the controller's interface.
Identifies and describes the function of the unit's external connectors.
Provides external dimensions and panel cutout details for installation.
Shows external dimensions for Current Transformer (CTL-6-S-H and CTL-12-S36-10L1U).
Describes the process for attaching and detaching the controller from a control panel.
Lists safety guidelines and best practices for electrical wiring.
Details the layout and function of each terminal connection on the controller.
Explains the use of solderless terminals and terminal covers for wiring.
Summarizes various wiring configurations for power supply, outputs, and inputs.
Provides a flowchart and description of key operations and mode transitions.
Explains the different operating modes (RUN, Monitor, Setting) and their functions.
Describes how to register settings, navigate menus, and return to RUN mode.
Details the steps for initial setup in Engineering and Control parameter modes.
Outlines the sequence for basic configuration and operation.
Explains how to set up program patterns for sequential control.
Details how to set Step SV, Step time, and PID block numbers for program patterns.
Explains how to configure event outputs, alarm values, and time signals.
Describes settings for AT, PID blocks, and control actions like Direct/Reverse.
Covers setting Wait value and enabling/disabling wait functions for program steps.
Details settings for value lock, sensor correction, and communication parameters.
Covers input types, scaling, decimal points, and event output allocations.
Explains how to reset the unit to factory default values.
Describes methods for starting and managing program control sequences.
Explains how to perform and finish fixed value control operations.
Details how to cycle through different indications on the SV display.
Explains how to perform AT and its impact on control parameters.
Describes how to adjust input values using sensor correction methods.
Shows which settings are reset when other parameters are modified.
Explains the behavior of OUT1 for heating/cooling and ON/OFF control.
Describes the action taken when a heater burnout condition is detected.
Illustrates various alarm conditions and their output actions.
Explains OUT2 behavior for heating/cooling control with dead/overlap bands.
Lists the technical specifications for the controller's performance and structure.
Details the specifications for various optional features and communication.
Describes additional features like sensor correction, self-diagnosis, and input error handling.
Lists problems related to display indications and their possible causes/solutions.
Covers troubleshooting for problems encountered with button inputs.
Addresses issues where the control action does not behave as expected.
Provides a list of error codes, their meanings, and occurrence conditions.
Compiles setting items and their ranges for various configuration modes.
Guides on how to create and document program patterns.
Explains how to create data tables for PID blocks and other settings.
Illustrates the sequence of operations using the controller's keys.
To Next Page
