Svantek SVAN 971 - Record with the Results

SVAN 971 User Manual – Appendixes
137
B.2.1.1. Record with the results
The contents of the record with the results depends on the selected measurement function and the value
set in the LOGGER position of the PROFILE x and SPECTRUM sub-lists. The following elements can be
present (in the given sequence):
16 flag record
< flags > :
- b0: 1- the overload detected, 0 - the overload not detected
- b1: 1- the excessive self-vibration detected, 0 - the excessive self-vibration overload not detected
17 results of the measurement from the first profile if the corresponding LOGGER position was active
(paths: Measurement / Logging / Logger Res. / Prof. 1); up to seven words are written:
<result1> - Lxpeak
1
result, depending on the value of BufferP[1] (cf. Tab. B.1.12)
<result2> - Lxymax
2
result, depending on the value of BufferP[1] (cf. Tab. B.1.12)
<result3> - Lxymin
2
result, depending on the value of BufferP[1] (cf. Tab. B.1.12)
<result4> - Lxyeq
23
result, depending on the value of BufferP[1] (cf. Tab. B.1.12)
<result5> - LAV result, depending on the value of BufferP[1] (cf. Tab. B.1.12)
<result6> - LR15 result, depending on the value of BufferP[1] (cf. Tab. B.1.12)
<result7> - LR60 result, depending on the value of BufferP[1] (cf. Tab. B.1.12)
(3) results of the measurement from the second profile if the corresponding LOGGER position was
active (paths: Measurement / Logging / Logger Res. / Prof. 2); up to five words are written:
<result1> - Lxpeak
1
result, depending on the value of BufferP[2] (cf. Tab. B.1.12)
<result2> - Lxymax
2
result, depending on the value of BufferP[2] (cf. Tab. B.1.12)
<result3> - Lxymin
2
result, depending on the value of BufferP[2] (cf. Tab. B.1.12)
<result4> - Lxyeq
23
result, depending on the value of BufferP[2] (cf. Tab. B.1.12)
<result5> - LAV result, depending on the value of BufferP[2] (cf. Tab. B.1.12)
(4) results of the measurement from the third profile if the corresponding LOGGER position was active
(paths: Measurement / Logging / Logger Res. / Prof. 3); up to five words are written:
<result1> - Lxpeak
1
result, depending on the value of BufferP[3] (cf. Tab. B.1.12)
<result2> - Lxymax
2
result, depending on the value of BufferP[3] (cf. Tab. B.1.12)
<result3> - Lxymin
2
result, depending on the value of BufferP[3] (cf. Tab. B.1.12)
<result4> - Lxyeq
23
result, depending on the value of BufferP[3] (cf. Tab. B.1.12)
<result5> - LAV result, depending on the value of BufferP[3] (cf. Tab. B.1.12)
1
x - depends of the filter type for Peak result calculation in selected profile: A, C, Z, B (cf.
Tab. B.1.12)
2
x - depends of the filter type in selected profile: A, C, Z, B (cf. Tab. B.1.12)
y - depends of the detector type in selected profile: I (imp.), F (fast), S (slow) (cf. Tab. B.1.12)
3
y - only for exponential detector's type (cf. Tab. B.1.6)
(5) results of 1/1 OCTAVE analysis or 1/3 OCTAVE analysis if 1/1 OCTAVE analysis or 1/3 OCTAVE
analysis was selected as the measurement function and the LOGGER was active (paths:
Measurement / Logging / Logger Res. / Peak Sp. [√] and Leq Sp. [√] );
the sequence of words is written: