YASKAWA GA800

1066 YASKAWA SIEPC71061737D GA800 Drive Technical Reference
Index
Symbols
Numerics
24 V power supply
Power supply input terminals..................................... 115
A
AC reactor
Wiring................................................................ 143
Acceleration and deceleration times
Switching by external input....................................... 769
Switching by output frequency ................................... 770
Switcing by Motor 2 Selection commands...................... 770
Acceleration time
Parameter ............................................................ 769
Unit of measurement setting ...................................... 772
Adjustment of control functionality .................................. 226
AEr........................................................................ 390
AFR
Parameter .......................................................... 1010
Alarm ............................................................... 352, 390
ALM indicator..................................................... 159, 162
ALM/ERR
LED status........................................................... 165
Altitude
Derating.............................................................. 507
Environment.......................................................... 36
Ambient humidity........................................................ 36
Ambient Temperature Setting .......................................... 36
Derating.............................................................. 505
Parameter .................................................... 506, 1001
Analog gauge
Monitors ............................................................. 181
Analog input
Function selection for terminals A1 through A3 ............... 929
Analog Output
Gain/Bias Adjustment ............................................. 942
Monitor Parameter Selection...................................... 942
Signal Level Selection ............................................. 942
Terminal AM Monitor Selection ................................. 944
Terminal FM Monitor Selection.................................. 944
Application Preset....................................................... 701
Operation ............................................................ 213
ASR
Closed Loop V/f Control adjustment procedure ............... 783
Fine tuning .......................................................... 785
Parameter ............................................................ 782
Vector Control Adjustment Procedure........................... 783
ASR tuning............................................................... 219
Precautions .......................................................... 223
Auto-Tuning ............................................................. 215
ASR and Inertia Tuning Parameters ........................... 1063
ASR tuning.......................................................... 219
Induction Motor .................................................... 215
Induction Motor Parameters .................................... 1057
Inertia Tuning ....................................................... 219
PM Motor Parameters............................................ 1060
PM Motors .......................................................... 216
Precautions .......................................................... 221
Precautions to Note before ASR Tuning ........................ 223
Precautions to Note before Inertia Tuning ...................... 223
Procedure ............................................................ 198
Rotational Auto-Tuning Precautions............................. 222
Stationary Auto-Tuning for Line-to-Line Resistance
precautions.................................................... 223
Stationary Auto-Tuning Precautions............................. 222
Stator resistance Auto-Tuning precautions...................... 223
Auto-Tuning Error ................................................ 352, 407
B
Backlight
Timing of shut-off .................................................. 209
Backup
Parameters (drive to keypad) ..................................... 190
Backup function....................................................... 1047
Bar graph
Monitors ............................................................. 179
Base frequency
Parameter ............................................................ 824
Base Frequency
Motor 2 Parameters ................................................ 829
Base voltage
Motor 2 parameters................................................. 830
Parameter ............................................................ 825
Basic operation
Get started ........................................................... 167
bAT
Fault .................................................................. 359
Minor Fault.......................................................... 390
Battery
Disposal.............................................................. 481
Replacement......................................................... 475
Specifications ....................................................... 475
bb.......................................................................... 390
bCE
Fault .................................................................. 359
Minor Fault.......................................................... 390
Bi-Directional function................................................. 809
boL
Fault .................................................................. 359
Minor Fault.......................................................... 390
Braking Resistor
Protective function ................................................. 998
Wiring................................................................ 130
bUS
Detection condition settings....................................... 869
Detection conditions ............................................... 865
Fault .................................................................. 359
Minor Fault.......................................................... 390
Operation Selection after Detection.............................. 864
bUSy ...................................................................... 391
C
CALL ..................................................................... 391
Capacitor Maintenance Setting...................................... 1049
Carrier frequency
Derating.............................................................. 500
Diminish ........................................................... 1004
Parameter ............................................................ 791
CDBR type braking unit
Connect multiple units............................................. 138
Wiring................................................................ 131
CE
Detection Selection................................................. 947