8-3
IM AQ7280-01EN
Troubleshooting, Maintenance, and Inspection
8
Code Message
513 ZERO SET ERROR
514 Exceeding limit. It may cause damage of the instrument. Please disconnect the plug.
515 ZERO SET ERROR
516 Fiber In Use Alarm Error 1
517 Fiber In Use Alarm Error 2
518 ZERO SET ERROR
519 ZERO SET ERROR
520 Hardware failed, and needs to be repaired. Please contact Yokogawa's representatives.
521 Operation is stopped outside of operating environmental condisions
522 Hardware failed, and needs to be repaired. Please contact Yokogawa's representatives.
524 Failure to initialize the option module.
525 The Interval is too short. Please change the inteval value.
526 Please set Avg Duration.
527 Need the AC power supply to measure. Please connect the AC adapter.
528 Free space is not enough. Please set the interval or the period again.
550 The event list does not exist in either of trace or both.
551 Measurement range of those two traces are not same reference points. Please set the origin (0m).
552 Fiber lengths do not match. The end point distance error between two traces must be within 3%.
553 Total number of events exceeds 100 for the 2-way analysis.
554 2-Way Trace cannot be executed due to difference in wavelengths of those two traces.
555 The differential trace cannot be created. Trace conditions are not same.
556 The differential trace cannot be created. No trace data available.
557 The differential trace cannot be created. The sampling resolutions are not same.
558 The differential trace cannot be created. The group indices are not same.
559 The differential trace cannot be created. The start points are not same.
560 When the event fix is ON, the distance reference setup cannot be performed.
561
1
-
2
has not been set. This function is effective only when
1
-
2
is set.
562 n-E has not been set. This function is effective only when n-E is set.
563 Conditions of the macro bending do not match.
601 Cannot save onto the media. This media is for read-only.
602 Can not recognize file system. -Internal memory: Contact Yokogawa's representatives. - USB memory or SD
card: Try the other media or format again with FAT
604 Storage media has been disconnected while the media is being accessed.
605 Same file name or folder name exists.
608 Invalid file name or folder name
609 Invalid file format
612 Invalid path name
614 Unknown file or folder
616 Cannot save onto the media. This media is for read-only.
620 Free space is not enough.
622 Unknown folder
623 Folder is not empty.
629 Writing to USB memory or SD card is not allowed.
634 Failed to delete the folder. Please confirm the following. - Media is correctly installed. - Media is formatted. -
Media is not read-only.
635 Failed to delete the folder. The path name or the file name is too long.
636 Failed to delete the folder. The hierarchy below the specified folder is too deep.
637 Failed to delete the folder. The path name is invalid.
638 The folder could not be deleted. Failed to delete files in the folder. Please confirm the following. - Media is correctly
installed. - Media is formatted. - Media is not read-only.
639 Failed to copy the folder. Please confirm the following. - Media is correctly installed. - Media is formatted. - Media
is not read-only.
640 Folder cannot be copied. The path name or the file name is too long.
641 Failed to copy the folder. The hierarchy below the specified folder is too deep.
642 Failed to copy the folder. The path name is invalid.
643 The folder copy could not be completed. Failed to create a destination folder. Please confirm the following.
- Media is correctly installed. - Media is formatted. - Media is not read-only.
644 The folder copy could not be completed. Failed to copy the files in the folder. Please confirm the following.
- Media is correctly installed. - Media is formatted. - Media is not read-only.
645 The path name is too long.
646 USB memory or SD card can not be recognized.
8.2 Error Messages
To Next Page
Loading...
Need help?
General
