ADVANTEST R3162 - Page 16

F-2
R3132 Series Spectrum Analyzer Operation Manual
List of Illustrations
No. Title Page
2-38 Screen Display Showing Reduced Harmonic Distortion .................................................. 2-46
2-39 Setup for Measuring Intermodulation ............................................................................... 2-46
2-40 Screen Display Showing Intermodulation Distortion ....................................................... 2-48
2-41 Screen Display without Intermodulation Distortion ......................................................... 2-48
2-42 Screen Display Showing the Cal Menu ............................................................................ 2-49
2-43 Editing the Correction Data Table .................................................................................... 2-50
2-44 Screen for the EMC Menu ................................................................................................ 2-51
2-45 Screen Display Showing the User-Definable Correction Data Table ............................... 2-51
2-46 Setup for the R3172 and Waveguide Mixer ..................................................................... 2-53
2-47 Setup for the R3182 and Waveguide Mixer ..................................................................... 2-53
2-48 Setup for Measuring the Channel Power .......................................................................... 2-55
2-49 Setting the Offset Level .................................................................................................... 2-56
2-50 Measuring the Channel power .......................................................................................... 2-57
2-51 Setup for Measuring the Occupied Bandwidth ................................................................. 2-58
2-52 Setting the Detector Mode ................................................................................................ 2-59
2-53 OBW Measurement Screen .............................................................................................. 2-60
2-54 OBW(95%) Measurement Screen .................................................................................... 2-60
2-55 Setup Measuring Adjacent Channel Leakage Power ........................................................ 2-62
2-56 PDC trace .......................................................................................................................... 2-63
2-57 CS/BS Setup dialog box ................................................................................................... 2-64
2-58 Root Nyquist Filter dialog box ......................................................................................... 2-65
2-59 ACP Measurement Display in Full Screen Mode ............................................................. 2-65
2-60 Measurement Using ACP GRAPH ................................................................................... 2-66
2-61 ACP at the 100 kHz .......................................................................................................... 2-66
2-62 Setup Measuring Adjacent Channel Leakage Power ........................................................ 2-67
2-63 PHS Trace ......................................................................................................................... 2-68
2-64 CS/BS Setup dialog box ................................................................................................... 2-69
2-65 Measurement Result in ACP Separate Screen Mode ........................................................ 2-70
2-66 Setup for Measuring a Burst Signal .................................................................................. 2-71
2-67 Burst Signal Displayed in Split Screen Mode .................................................................. 2-72
2-68 Trigger Setup .................................................................................................................... 2-73
2-69 Gate Setup ......................................................................................................................... 2-73
2-70 Burst Signal by Use of the Gated Sweep (Separate Screen Mode) .................................. 2-74
2-71 Burst Signal by Use of the Gated Sweep (Full Screen Mode) .......................................... 2-74
2-72 Setup for Measuring a Burst wave signal ......................................................................... 2-75
2-73 Burst Signal in the Time Domain ..................................................................................... 2-76
2-74 Burst Signal in the Time Domain ..................................................................................... 2-76
2-75 Burst Signal in Synchronization with the Trigger Signal ................................................. 2-77
2-76 Measuring Burst Signal Leading Edge ............................................................................. 2-77
2-77 Measuring Burst Signal Trailing Edge ............................................................................. 2-78
2-78 Screen Displayed after Limit Line 1 Data Has Been Entered .......................................... 2-81
2-79 Screen Displayed after Limit Line 2 Data Has Been Entered .......................................... 2-81
2-80 PASS/FAIL Result using Limit Line 1 (PASS) ................................................................ 2-82
2-81 PASS/FAIL Result using Limit Lines 1 and 2 (FAIL) ..................................................... 2-82
2-82 PASS/FAIL Result using Limit Lines 1 and 2 (PASS) .................................................... 2-83
2-83 Judgment Result after the Offset Has Been Changed (FAIL) .......................................... 2-83
2-84 Judgment Result after the Offset Has Been Changed (PASS) .......................................... 2-84
2-85 Setup for TG Measurements ............................................................................................. 2-85