BERTHOLD TECHNOLOGIES LB 480

To Next Page

To Previous Page

54733-10BA2L

2 – 222 02.2017

3 Electrical Installation Volume 2

Signal cable with shielding We recommend using a screened cable for the signal lines.

The screen has to be connected to the detector on the PE terminal

in the terminal compartment of the detector, or better, to suitable

EMC cable glands.

Main Page

Default Chapter5
- Table of Contents5
About this User's Manual13
- Typographical Conventions13
- Meaning of Other Symbols Used in this Documentation14
- Meaning of Warning Signs on Detectors and Source Shieldings14
- Terms Used in this User's Manual15
- General Information16
Proper Use17
Qualification of Personnel19
- Persons with a General Knowledge19
- Experts20
- Authorized Persons20
Transport and Assembly21
Explosion Protection23
- Declaration of Conformity25
- General Information26
- Improper Use26
- Safety Instructions27
- Application Range and Technical Data28
- Installation34
- Ex - Concept40
- Maintenance and Visual Inspection49
- ATEX Certificate55
- Iecex Certificate65
- FM Certificate81
- Electrical Installation87
- Functional Safety91
- Visual Inspection111
- Radiation Protection113
Source Replacement129
- Radiation Exposure During Source Replacement129
- Point Source Replacement on Rotary Cylinder Shielding131
- Rod Source Replacement135
- Point Source Replacement on LB 744X Shieldings140
Source Disposal145
System Description151
- Measuring System151
- Sensseries Hardware154
- Measuring Principle157
- Measuring Arrangements158
- Technical Data162
- Detector Codes166
- Nomenclature of the Sensseries LB 480167
Installation171
- Transport to the Installation Site173
- Source Detector Arrangements175
- Detector Protection177
- Detector Assembly180
- Water Cooling187
- Shielding189
Electrical Installation217
- Cable Entries217
- Terminals219
- Connecting the Detector223
Repair, Maintenance and Upkeep227
- Safety Instructions228
- Replacing the Complete Detector229
- Replacing the Electronics Module231
- Replacing the Crystal-Multiplier Assembly (for Crystalsens)234
- Checking the Detector235
- Customer Service238
- Repair, Return Shipping239
Technical Information241
- TI LB 480 Level241
- TI LB 480 Towersens276
Accessories289
- Cable Glands289
- Limit Switches for Pneumatics292
- Volume 2294
  - Operation with HART Communicator299
  - Volume 3 Operation with299
HART ® Communication301
- HART® Protocol301
- General Information on the HART Communicator301
- Connection, Power on and Power off of the HART ® Communicator302
- Working with the HART ® Communicator302
- Archiving Parameter Sets303
Menu Structure307
- Information on the Menu Structure307
- Menu Overview308
- Start Menu313
- Live Display314
- Device Config316
- Setup316
- Quick Start317
- Quick Start, Step 1317
- Quick Start, Step 2318
- Quick Start, Step 3318
- Sensor Configuration322
- Date & Time323
- Sensor Settings324
- Config Slave Detectors327
- Signal Condition328
- Signal Parameter329
- Reading Range330
- Signal Dependency331
- Source Exchange333
- Cal Parameter335
- Cal Points337
- Cal Settings341
- Product Conditions343
- Calc Comp Factor349
- Adapt Calibration350
- Adjust Lower Point351
- Adjust Upper Point353
- I/O Setup354
- Current Output355
- Digital Output357
- Level Threshold Settings359
- Temp. Threshold Settings360
- Digital Input361
- HART Interface362
- Service363
- Pmt364
- Sensor Temperature365
- Test366
- Test Settings366
- I/O Test Settings369
- Plateau370
- Plateau Measurement371
- Plateau View372
- Plateau Information372
- Meas Parameter373
- Meas Data373
- Meas Settings374
- Meas Readings375
- Access376
- Identification378
- Location378
- Device Information379
- Device Revision380
- Diagnostic381
- Operating Status382
- Ext Dev Status382
- Device Variables Status383
- Config Change Status383
- Lock Device Status383
- Error Status384
- Log387
- Error Log387
- Modification Log388
Getting Started Via the HART389
- Steps for Getting Started389
Quick Guide to Calibration391
- Communicator391
Calibration393
- Preparing Calibration394
- Calibration with Quick Start396
- Ensuring the Function of the Measurement402
Functional Processes405
- Multidetector Operation405
- Plateau Measurement406
- Master Reset408
Explanations411
- Background411
- Conditions for Empty Calibration413
- Linear and Exponential415
- Multi-Point Calibration417
- Radiation Interference Detection420
- Time Constant423
- Software Versions424
Error Handling429
- Error Handling Modes429
- Device Response to Errors430
- Trouble Shooting437
- Reset438
- Operation Modes During Measurement438
- Error Reset438
- Fault Current439
Setup Protocol441

BERTHOLD TECHNOLOGIES LB 480 - Page 222

Table of Contents

Related product manuals