BERTHOLD TECHNOLOGIES LB 480

To Previous Page

Subject to change in the course of further technical development.

02.2017 Rev. No.: 03

BERTHOLD TECHNOLOGIES GmbH & Co. KG

Calmbacher Str. 22

D-75323 Bad Wildbad

Germany

www.Berthold.com ID No. 54733-10BA2L

Main Page

Default Chapter5
- Table of Contents5
About this User's Manual13
- Typographical Conventions13
- Meaning of Other Symbols Used in this Documentation14
- Meaning of Warning Signs on Detectors and Source Shieldings14
- Terms Used in this User's Manual15
- General Information16
Proper Use17
Qualification of Personnel19
- Persons with a General Knowledge19
- Experts20
- Authorized Persons20
Transport and Assembly21
Explosion Protection23
- Declaration of Conformity25
- General Information26
- Improper Use26
- Safety Instructions27
- Application Range and Technical Data28
- Installation34
- Ex - Concept40
- Maintenance and Visual Inspection49
- ATEX Certificate55
- Iecex Certificate65
- FM Certificate81
- Electrical Installation87
- Functional Safety91
- Visual Inspection111
- Radiation Protection113
Source Replacement129
- Radiation Exposure During Source Replacement129
- Point Source Replacement on Rotary Cylinder Shielding131
- Rod Source Replacement135
- Point Source Replacement on LB 744X Shieldings140
Source Disposal145
System Description151
- Measuring System151
- Sensseries Hardware154
- Measuring Principle157
- Measuring Arrangements158
- Technical Data162
- Detector Codes166
- Nomenclature of the Sensseries LB 480167
Installation171
- Transport to the Installation Site173
- Source Detector Arrangements175
- Detector Protection177
- Detector Assembly180
- Water Cooling187
- Shielding189
Electrical Installation217
- Cable Entries217
- Terminals219
- Connecting the Detector223
Repair, Maintenance and Upkeep227
- Safety Instructions228
- Replacing the Complete Detector229
- Replacing the Electronics Module231
- Replacing the Crystal-Multiplier Assembly (for Crystalsens)234
- Checking the Detector235
- Customer Service238
- Repair, Return Shipping239
Technical Information241
- TI LB 480 Level241
- TI LB 480 Towersens276
Accessories289
- Cable Glands289
- Limit Switches for Pneumatics292
- Volume 2294
  - Operation with HART Communicator299
  - Volume 3 Operation with299
HART ® Communication301
- HART® Protocol301
- General Information on the HART Communicator301
- Connection, Power on and Power off of the HART ® Communicator302
- Working with the HART ® Communicator302
- Archiving Parameter Sets303
Menu Structure307
- Information on the Menu Structure307
- Menu Overview308
- Start Menu313
- Live Display314
- Device Config316
- Setup316
- Quick Start317
- Quick Start, Step 1317
- Quick Start, Step 2318
- Quick Start, Step 3318
- Sensor Configuration322
- Date & Time323
- Sensor Settings324
- Config Slave Detectors327
- Signal Condition328
- Signal Parameter329
- Reading Range330
- Signal Dependency331
- Source Exchange333
- Cal Parameter335
- Cal Points337
- Cal Settings341
- Product Conditions343
- Calc Comp Factor349
- Adapt Calibration350
- Adjust Lower Point351
- Adjust Upper Point353
- I/O Setup354
- Current Output355
- Digital Output357
- Level Threshold Settings359
- Temp. Threshold Settings360
- Digital Input361
- HART Interface362
- Service363
- Pmt364
- Sensor Temperature365
- Test366
- Test Settings366
- I/O Test Settings369
- Plateau370
- Plateau Measurement371
- Plateau View372
- Plateau Information372
- Meas Parameter373
- Meas Data373
- Meas Settings374
- Meas Readings375
- Access376
- Identification378
- Location378
- Device Information379
- Device Revision380
- Diagnostic381
- Operating Status382
- Ext Dev Status382
- Device Variables Status383
- Config Change Status383
- Lock Device Status383
- Error Status384
- Log387
- Error Log387
- Modification Log388
Getting Started Via the HART389
- Steps for Getting Started389
Quick Guide to Calibration391
- Communicator391
Calibration393
- Preparing Calibration394
- Calibration with Quick Start396
- Ensuring the Function of the Measurement402
Functional Processes405
- Multidetector Operation405
- Plateau Measurement406
- Master Reset408
Explanations411
- Background411
- Conditions for Empty Calibration413
- Linear and Exponential415
- Multi-Point Calibration417
- Radiation Interference Detection420
- Time Constant423
- Software Versions424
Error Handling429
- Error Handling Modes429
- Device Response to Errors430
- Trouble Shooting437
- Reset438
- Operation Modes During Measurement438
- Error Reset438
- Fault Current439
Setup Protocol441

BERTHOLD TECHNOLOGIES LB 480 - Page 450

Table of Contents

Related product manuals