EasyManuals Logo

Brocade Communications Systems FastIron X Series User Manual

Brocade Communications Systems FastIron X Series
593 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #265 background imageLoading...
Page #265 background image
Modify OSPF traps generated
OSPF traps as dened by RFC 1850 are supported on device.
You can disable all or specic OSPF trap generation by entering the following CLI command.
device(config)# no snmp-server trap ospf
To later re-enable the trap feature, enter snmp-server trap ospf .
To disable a
specic OSPF trap, enter the command as no snmp-server trap ospf ospf-trap.
These commands are at the OSPF router Level of the CLI.
Here is a summary of OSPF traps supported on device, their corresponding CLI commands, and their associated MIB objects from RFC
1850. The rst list are traps enabled by default:
• interface-state-change-trap - [MIB object: OspfIfstateChange]
• virtual-interface-state-change-trap - [MIB object: OspfVirtIfStateChange
• neighbor-state-change-trap - [MIB object:ospfNbrStateChange]
• virtual-neighbor-state-change-trap - [MIB object: ospfVirtNbrStateChange]
• interface-cong-error-trap - [MIB object: ospfIfCongError]
• virtual-interface-cong-error-trap - [MIB object: ospfVirtIfCongError]
• interface-authentication-failure-trap - [MIB object: ospfIfAuthFailure]
• virtual-interface-authentication-failure-trap - [MIB object: ospfVirtIfAuthFailure]
• interface-receive-bad-packet-trap - [MIB object: ospfIfrxBadPacket]
• virtual-interface-receive-bad-packet-trap - [MIB object: ospfVirtIfRxBadPacket]
The following traps are disabled by default.
• interface-retransmit-packet-trap - [MIB object: ospfTxRetransmit]
• virtual-interface-retransmit-packet-trap - [MIB object: ospfVirtIfTxRetransmit]
• originate-lsa-trap - [MIB object: ospfOriginateLsa]
• originate-maxage-lsa-trap - [MIB object: ospfMaxAgeLsa]
• link-state-database-overow-trap - [MIB object: ospfLsdbOverow]
• link-state-database-approaching-overow-trap - [MIB object: ospfLsdbApproachingOverow
To stop an OSPF trap from being collected, use the CLI command: no trap ospf-trap at the Router OSPF level of the CLI. To disable
reporting of the neighbor-state-change-trap, enter the following command.
device(config-ospf-router)# no trap neighbor-state-change-trap
To reinstate the trap, enter the following command.
device(config-ospf-router)# trap neighbor-state-change-trap
Syntax: [no] trap ospf-trap
Modify exit overow interval
If a database overow condition occurs on a router, the router eliminates the condition by removing entries that originated on the router.
The exit overow interval allows you to set how often a device checks to see if the overow condition has been eliminated. The default
value is 0. The range is 0 - 86400 seconds (24 hours). If the congured value of the database overow interval is zero, then the router
never leaves the database overow condition.
OSPF distribute list
FastIron Ethernet Switch Layer 3 Routing
53-1003627-04 265

Table of Contents

Other manuals for Brocade Communications Systems FastIron X Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Brocade Communications Systems FastIron X Series and is the answer not in the manual?

Brocade Communications Systems FastIron X Series Specifications

General IconGeneral
BrandBrocade Communications Systems
ModelFastIron X Series
CategorySwitch
LanguageEnglish

Related product manuals