EasyManuals Logo

Brocade Communications Systems FastIron X Series User Manual

Brocade Communications Systems FastIron X Series
593 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #527 background imageLoading...
Page #527 background image
Conguring IPv4 VRRP-E
VRRP-E is congured at the interface level. To implement a simple IPv4 VRRP-E conguration using all the default values, enter
commands such as the following on each Layer 3 switch.
Brocade(config)#router vrrp-extended
Brocade(config)#interface ethernet 1/1/5
Brocade(config-if-1/1/5)#ip-address 192.53.5.3
Brocade(config-if-1/1/5)#ip vrrp-extended vrid 1
Brocade(config-if-1/1/5-vrid-1)#backup
Brocade(config-if-1/1/5-vrid-1)#advertise backup
Brocade(config-if-1/1/5-vrid-1)#ip-address 192.53.5.254
Brocade(config-if-1/1/5-vrid-1)#activate
Syntax: [no] router vrrp-extended
Syntax: [no] ip-address ip-address
Syntax: [no] ip vrrp-extended vrid vrid
Syntax: no backup [ priority value ] [ track-priority value ]
Syntax: [no] advertise backup
Syntax: [no] activate
The vrid variable
species the virtual router ID.
The ip-address variable species the IPv4 address of the router.
You must identify a VRRP-E router as a Backup before you can activate the virtual router on a Brocade device. However, after you
congure the virtual router, you can use the backup command to change its priority or track priority.
The priority value option species the IPv4 VRRP-E priority for this virtual Backup router. You can specify a value from 3 through 254.
The default is 100.
The track-priority value option changes the track port priority of a Backup router. You can specify a value from 1 through 254. The
default is 5.
NOTE
You also can use the enable command to activate the conguration. This command does the same thing as the activate
command.
Conguring IPv6 VRRP-E
To implement an IPv6 VRRP-E conguration using all the default values, enter the following commands.
NOTE
You must rst congure the ipv6 unicast-routing command at the global conguration level to enable IPv6 VRRP-E on the
router.
Brocade(config)# ipv6 unicast-routing
Brocade(config)# ipv6 router vrrp-extended
Brocade(config-ipv6-VRRP-E-router)# interface ethernet 1/1/5
Brocade(config-if-e10000-1/1/5)# ipv6-address 2001:DB8::2/64
Brocade(config-if-e10000-1/1/5)# ipv6 vrrp-extended vrid 1
Brocade(config-if-e10000-1/1/5-vrid-1)# backup priority 50 track-priority 10
Brocade(config-if-e10000-1/1/5-vrid-1)# ipv6-address 2001:DB8::99
Brocade(config-if-e10000-1/1/5-vrid-1)# activate
Syntax: [no] ipv6 unicast-routing
Basic VRRP-E parameter conguration
FastIron Ethernet Switch Layer 3 Routing
53-1003627-04 527

Table of Contents

Other manuals for Brocade Communications Systems FastIron X Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Brocade Communications Systems FastIron X Series and is the answer not in the manual?

Brocade Communications Systems FastIron X Series Specifications

General IconGeneral
BrandBrocade Communications Systems
ModelFastIron X Series
CategorySwitch
LanguageEnglish

Related product manuals