TABLE 64 show ip ospf database database-summary output descriptions (continued)
This eld Displays
NSSA-Ext The number of not-so-stubby
Opq-area the number of Type-10 (area-scope) Opaque LSA.s
Displaying OSPF database link state information
To display database link state information, enter the following command at any CLI level.
device# show ip ospf database link-state
Index Area ID Type LS ID Adv Rtr Seq(Hex) Age Cksum SyncState
1 0 Rtr 10.1.10.1 10.1.10.1 800060ef 3 0x4be2 Done
2 0 Rtr 10.65.12.1 10.65.12.1 80005264 6 0xc870 Done
3 0 Net 10.1.64.2 10.65.12.1 8000008c 1088 0x06b7 Done
4 0 Net 10.1.167.2 10.65.12.1 80000093 1809 0x86c8 Done
5 0 Net 10.1.14.2 10.65.12.1 8000008c 1088 0x2ec1 Done
6 0 Net 10.1.117.2 10.65.12.1 8000008c 1087 0xbccb Done
7 0 Net 10.1.67.2 10.65.12.1 8000008c 1088 0xe4d5 Done
8 0 Net 10.1.170.2 10.65.12.1 80000073 604 0xa5c6 Done
9 0 Net 10.1.17.2 10.65.12.1 8000008c 1088 0x0ddf Done
10 0 Net 10.1.120.2 10.65.12.1 8000008c 1087 0x9be9 Done
11 0 Net 10.1.70.2 10.65.12.1 8000008c 1088 0xc3f3 Done
12 0 Net 10.1.173.2 10.65.12.1 80000017 1087 0x3d88 Done
13 0 Net 10.1.20.2 10.65.12.1 8000008c 1088 0xebfd Done
14 0 Net 10.1.123.2 10.65.12.1 8000008c 1087 0x7a08 Done
15 0 Net 10.1.73.2 10.65.12.1 8000008c 1088 0xa212 Done
16 0 Net 10.1.176.2 10.65.12.1 80000025 1087 0xffb4 Done
17 0 Net 10.1.23.2 10.65.12.1 8000008c 1088 0xca1c Done
18 0 Net 10.1.126.2 10.65.12.1 8000008c 1087 0x5926 Done
Syntax:show ip ospf [ vrf vrf-name] database link-state [ advertise num | asbr [ ip-addr ] [ adv-router ip-addr ] | extensive |link-state-
id ip-addr | network [ ip-addr ] [ adv-router ip-addr ] | nssa [ ip-addr ] [ adv-router ip-addr ] | router [ ip-addr ] [ adv-router ip-addr ] |
router-id ip-addr | self-originate I sequence-number num(Hex) | summary [ ip-addr ] [ adv-router ip-addr ]
The vrf vrf-name parameter displays information for a VRF, or a
specic vrf-name.
The advertise num parameter displays the decoded data in the specied LSA packet. The num parameter identies the LSA packet by
its position in the router’s LSA table. To determine an LSA packet’s position in the table, enter the show ip ospf link-state command to
display the table.
The asbr option shows ASBR LSAs.
The extensive option displays the LSAs in the decoded format.
NOTE
You cannot use the extensive option in combination with other display options. The entire database is displayed.
The link-state-id A.B.C.D parameter displays the LSAs for the LSA source specied by A.B.C.D (link state ID).
The network option shows network LSAs.
The nssa option shows NSSA LSAs.
The router-id A.B.C.D (advertising router ID) parameter shows the LSAs for the specied OSPF router.
The sequence-number num parameter displays the LSA entries for the specied hexadecimal LSA sequence number.
Displaying OSPF information
FastIron Ethernet Switch Layer 3 Routing
53-1003627-04 283
To Next Page
Loading...
Need help?
General
