TABLE 60 show ip ospf interface brief output descriptions (continued)
This eld Displays
or greater are used by the ooding procedure. In fact, these
adjacencies are fully capable of transmitting and receiving all
types of OSPF routing protocol packets.
• Loading - Link State Request packets are sent to the neighbor
asking for the more recent advertisements that have been
discovered (but not yet received) in the Exchange state.
• Full - The neighboring routers are fully adjacent. These
adjacencies will now appear in router links and network link
advertisements.
Nbrs(F/C) The number of adjacent neighbor routers. The number to the left of the "/"
are the neighbor routers that are fully adjacent and the number to the right
represents all adjacent neighbor routers.
Displaying OSPF route information
To display OSPF route information, enter the following command at any CLI level.
device# show ip ospf route
OSPF Area 0x00000000 ASBR Routes 1:
Destination Mask Path_Cost Type2_Cost Path_Type
10.65.12.1 255.255.255.255 1 0 Intra
Adv_Router Link_State Dest_Type State Tag Flags
10.65.12.1 10.65.12.1 Asbr Valid 0 6000
Paths Out_Port Next_Hop Type State
1 v49 10.1.49.2 OSPF 21 01
2 v12 10.1.12.2 OSPF 21 01
3 v11 10.1.11.2 OSPF 21 01
4 v10 10.1.10.2 OSPF 00 00
OSPF Area 0x00000041 ASBR Routes 1:
Destination Mask Path_Cost Type2_Cost Path_Type
10.65.12.1 255.255.255.255 1 0 Intra
Adv_Router Link_State Dest_Type State Tag Flags
10.65.12.1 10.65.12.1 Asbr Valid 0 6000
Paths Out_Port Next_Hop Type State
1 v204 10.65.5.251 OSPF 21 01
2 v201 10.65.2.251 OSPF 20 d1
3 v202 10.65.3.251 OSPF 20 cd
4 v205 10.65.6.251 OSPF 00 00
OSPF Area Summary Routes 1:
Destination Mask Path_Cost Type2_Cost Path_ Type
10.65.0.0 255.255.0.0 0 0 Inter
Adv_Router Link_State Dest_Type State Tag Flags
10.1.10.1 0.0.0.0 Network Valid 0 0000
Paths Out_Port Next_Hop Type State
1 1/1 0.0.0.0 DIRECT 00 00
OSPF Regular Routes 208:
Destination Mask Path_Cost Type2_Cost Path_Type
10.1.10.0 255.255.255.252 1 0 Intra
Adv_Router Link_State Dest_Type State Tag Flags
10.1.10.1 10.1.10.2 Network Valid 0 0000
Paths Out_Port Next_Hop Type State
1 v10 0.0.0.0 OSPF 00 00
Destination Mask Path_Cost Type2_Cost Path_Type
10.1.11.0 255.255.255.252 1 0 Intra
Adv_Router Link_State Dest_Type State Tag Flags
10.1.10.1 10.1.11.2 Network Valid 0 0000
Paths Out_Port Next_Hop Type State
1 v11 0.0.0.0 OSPF 00 00
Syntax: show ip ospf routes [ ip-addr ]
The ip-addr parameter
species a destination IP address. If you use this parameter, only the route entries for that destination are shown.
Displaying OSPF information
FastIron Ethernet Switch Layer 3 Routing
53-1003627-04 279
To Next Page
Loading...
Need help?
General
