EasyManuals Logo

Brocade Communications Systems FastIron X Series User Manual

Brocade Communications Systems FastIron X Series
593 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #339 background imageLoading...
Page #339 background image
Displaying OSPFv3 GR Helper mode information
Run the show ipv6 ospf command to display information about the graceful restart helper mode
device# (config-ospf6-router)#show ipv6 ospf
OSPFv3 Process number 0 with Router ID 0xa19e0eb(10.25.224.235)
Running 0 days 0 hours 0 minutes 26 seconds
Number of AS scoped LSAs is 0
Sum of AS scoped LSAs Checksum is 0
External LSA Limit is 250000
Database Overflow Interval is 10
Database Overflow State is NOT OVERFLOWED
Route calculation executed 0 times
Pending outgoing LSA count 0
Authentication key rollover interval 300 seconds
Number of areas in this router is 0
High Priority Message Queue Full count: 0
Graceful restart helper is enabled, strict lsa checking is disabled
Nonstop-routing is ENABLED
Displaying OSPFv3 NSR information
Run the show ipv6 ospf command to display information about the NSR support.
device# (config-ospf6-router)#show ipv6 ospf
OSPFv3 Process number 0 with Router ID 0xa19e0eb(10.25.224.235)
Running 0 days 0 hours 0 minutes 26 seconds
Number of AS scoped LSAs is 0
Sum of AS scoped LSAs Checksum is 0
External LSA Limit is 250000
Database Overflow Interval is 10
Database Overflow State is NOT OVERFLOWED
Route calculation executed 0 times
Pending outgoing LSA count 0
Authentication key rollover interval 300 seconds
Number of areas in this router is 0
High Priority Message Queue Full count: 0
Graceful restart helper is enabled, strict lsa checking is disabled
Nonstop-routing is ENABLED
Displaying IPv6 OSPF virtual link information
To display OSPFv3 virtual link information on a Brocade device, enter the show ipv6 ospf virtual-link command at any level of the CLI.
device# show ipv6 ospf virtual-link
Transit Area ID Router ID Interface Address State
0.0.0.200 192.168.98.111 5100::192:213:111:213 P2P
Timer intervals(sec) :
Hello 10, Hello Jitter 10, Dead 40, Retransmit 5, TransmitDelay 1
DelayedLSAck: 65 times
Authentication: Not Configured
Statistics:
Type tx rx tx-byte rx-byte
Unknown 0 0 0 0
Hello 819 816 32760 32640
DbDesc 10 11 300 11008
LSReq 6 0 6492 0
LSUpdate 1579 1161 138284 101488
LSAck 65 52 29340 29532
OSPF messages dropped,no authentication: 0
Neighbor: State: Full Address: 5100::192:113:111:111 Interface: e 4/3/1
Syntax: show ipv6 opsf virtual-link
Displaying OSPFv3 information
FastIron Ethernet Switch Layer 3 Routing
53-1003627-04 339

Table of Contents

Other manuals for Brocade Communications Systems FastIron X Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Brocade Communications Systems FastIron X Series and is the answer not in the manual?

Brocade Communications Systems FastIron X Series Specifications

General IconGeneral
BrandBrocade Communications Systems
ModelFastIron X Series
CategorySwitch
LanguageEnglish

Related product manuals