RouteReflectorClient: yes
SendCommunity: yes
NextHopSelf: yes
DefaultOriginate: yes (default sent)
MaximumPrefixLimit: 90000
RemovePrivateAs: : yes
RefreshCapability: Received
Route Filter Policies:
Distribute-list: (out) 20
Filter-list: (in) 30
Prefix-list: (in) pf1
Route-map: (in) setnp1 (out) setnp2
Messages: Open Update KeepAlive Notification Refresh-Req
Sent : 1 1 1 0 0
Received: 1 8 1 0 0
Last Update Time: NLRI Withdraw NLRI Withdraw
Tx: 0h0m59s --- Rx: 0h0m59s ---
Last Connection Reset Reason:Unknown
Notification Sent: Unspecified
Notification Received: Unspecified
TCP Connection state: ESTABLISHED
Local host: 10.4.0.1, Local Port: 179
Remote host: 10.4.0.2, Remote Port: 8053
ISentSeq: 52837276 SendNext: 52837392 TotUnAck: 0
TotSent: 116 ReTrans: 0 UnAckSeq: 52837392
IRcvSeq: 2155052043 RcvNext: 2155052536 SendWnd: 16384
TotalRcv: 493 DupliRcv: 0 RcvWnd: 16384
SendQue: 0 RcvQue: 0 CngstWnd: 1460
This example shows how to display information for a
specic neighbor, by specifying the neighbor’s IP address with the command. Since
none of the other display options are used, all of the information is displayed for the neighbor. The number in the far left column indicates
the neighbor for which information is displayed. When you list information for multiple neighbors, this number makes the display easier
to read.
The TCP statistics at the end of the display show status for the TCP session with the neighbor. Most of the elds show information stored
in the Transmission Control Block (TCB) for the TCP session between the device and the neighbor. These elds are described in detail in
section 3.2 of RFC 793, "Transmission Control Protocol Functional Specication".
Syntax: show ip bgp neighbors [ ip-addr [ advertised-routes [ detail [ ip-add [ / mask-bits ] ] ] ] | [ attribute-entries [ detail ] ] | [ ap-
statistics ] | [ last-packet-with-error ] | [ received prex-lter ] | [ received-routes ] | [ routes [ best ] | [ detail [ best ] | [ not-installed-
best ] | [ unreachable ] ] | [ rib-out-routes [ ip-addr/mask-bits | ip-addr net-mask | detail ] ] | [ routes-summary ] ]
The ip-addr option lets you narrow the scope of the command to a specic neighbor.
The advertised-routes option displays only the routes that the device has advertised to the neighbor during the current BGP4 session.
The attribute-entries option shows the attribute-entries associated with routes received from the neighbor.
The ap-statistics option shows the route ap statistics for routes received from or sent to the neighbor.
The last-packet-with-error option displays the last packet from the neighbor that contained an error. The packet contents are displayed
in decoded (human-readable) format.
The received prex-lter option shows the Outbound Route Filters (ORFs) received from the neighbor. This option applies to
cooperative route ltering.
The received-routes option lists all the route information received in route updates from the neighbor since the soft reconguration
feature was enabled.
The routes option lists the routes received in UPDATE messages from the neighbor. You can specify the following additional options:
• best - Displays the routes received from the neighbor that the device selected as the best routes to their destinations.
Displaying BGP4 information
FastIron Ethernet Switch Layer 3 Routing
444 53-1003627-04
To Next Page
Loading...
Need help?
General
