Bruker HYPERION - Page 177

Bruker Optik GmbH HYPERION - User Manual
Index
Numerics
15x GIR objective ...................................111
15x objective
.................. 44, 63, 68, 77, 161
Plastic shroud ........................................110
20x ATR objective
...................................111
36x objective
.................................. 111, 162
40x objective
...........................................161
4x objective
................ 44, 77, 111, 150, 161
A
Analysis system
Switching off ............................................57
Switching on ............................................56
Analyzer
........................................... 52, 121
Aperture
....................................................51
Diameter ...............................................113
Installation locations ........................ 39, 114
Measurement spot diameter ....................113
Overview ........................................ 37, 113
ATR crystal assembly
.............................137
ATR objective
72, 86, 111, 135, 153, 155, 162
Aligning the crystal centrically ..................142
Attaching at the revolving nosepiece ..........87
Checking the crystal position for centrality .141
Checking the height setting of the crystal ..143
Connecting to the microscope ...................87
Contact pressure ....................................162
Contact pressure level ..............................72
Contact pressure levels ............................89
Correcting the height setting of the crystal .144
Crystal material ......................................162
Crystal tip diameter ................................162
Focussing in measuring mode ...................90
Focussing in viewing mode .......................89
Handling instructions ................................86
In-focus LED ...................... 73, 90, 98, 144
Mapping measurement procedure ..............95
Replacing the crystal assembly ................136
Single point measurement procedure .........91
ATR objective crystal
Checking for damages ............................135
Cleaning .................................................86
Measuring mode position ................... 72, 88
Viewing mode position ..............................88
B
Beam attenuator 76, 123, 124, 158, 159, 160
Beam path
................................................49
HYPERION 1000 and 2000 .......................49
HYPERION 3000 .....................................50
Binocular
..............26, 29, 42, 45, 51, 64, 68
Brightness
Setting ....................................................77
Brightness control
...............................27, 30
Brightness indicator
............................29, 30
C
Coarse focus ......................................27, 33
Coarse focus knob
....................................33
Compression cell
................... 124, 149, 152
Condenser
.26, 28, 33, 36, 52, 63, 149, 152
Centering screws ...............................36, 65
Checking the setting .................................63
Correcting the setting ...............................65
Condenser focussing knob
.......... 33, 36, 65
Control panel
............................................26
D
Data cable ................................................10
Detector
................. 27, 28, 47, 51, 151, 153
Checking the saturation ............................75
Installation locations .................................47
Mode of cooling .....................................163
Nominal hold time ..................................163
Overview of single-element detectors .......163
Sensitivity .............................................163
Spectral range .......................................163
Detector evacuation
Required equipment ...............................130
Detector oversaturation
............................76
Detector temperature warning indicator
...30
E
Environmental conditions
Ambient temperature range .......................11
Ambient temperature variations .................11
Humidity .................................................11
Experiment file
........................................167
Modifying ..............................................168
External power supply unit
.......... 10, 13, 14
External sample cabinet
.........................123
F
Filling hole for detector .............................60
Fine focus
...........................................27, 33
Fine focus knob
........................................33
Focussing
.................................................77
FPA detector
........25, 47, 48, 158, 159, 164
Cooling .............................................59, 61
Mode of cooling .....................................164
Nominal hold time ............................61, 164
Number of detector elements ..................164
ON / OFF switch ..............................57, 128
Removing / reinstalling ...........................128
Spectral range .......................................164