EasyManuals Logo

Cisco ME 3400 User Manual

Cisco ME 3400
1138 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1052 background imageLoading...
Page #1052 background image
B-14
Cisco ME 3400 Ethernet Access Switch Software Configuration Guide
OL-9639-07
Appendix B Working with the Cisco IOS File System, Configuration Files, and Software Images
Working with Configuration Files
This example shows how to copy a configuration file named host1-confg from the netadmin1 directory
on the remote server with an IP address of 172.16.101.101 and to load and run those commands on the
switch:
Switch# copy ftp://netadmin1:mypass@172.16.101.101/host1-confg system:running-config
Configure using host1-confg from 172.16.101.101? [confirm]
Connected to 172.16.101.101
Loading 1112 byte file host1-confg:![OK]
Switch#
%SYS-5-CONFIG: Configured from host1-config by ftp from 172.16.101.101
This example shows how to specify a remote username of netadmin1. The software copies the
configuration file host2-confg from the netadmin1 directory on the remote server with an IP address
of
172.16.101.101 to the switch startup configuration.
Switch# configure terminal
Switch(config)# ip ftp username netadmin1
Switch(config)# ip ftp password mypass
Switch(config)# end
Switch# copy ftp: nvram:startup-config
Address of remote host [255.255.255.255]? 172.16.101.101
Name of configuration file[rtr2-confg]? host2-confg
Configure using host2-confg from 172.16.101.101?[confirm]
Connected to 172.16.101.101
Loading 1112 byte file host2-confg:![OK]
[OK]
Switch#
%SYS-5-CONFIG_NV:Non-volatile store configured from host2-config by ftp from
172.16.101.101
Uploading a Configuration File By Using FTP
Beginning in privileged EXEC mode, follow these steps to upload a configuration file by using FTP:
Command Purpose
Step 1
Verify that the FTP server is properly configured by referring
to the
“Preparing to Download or Upload a Configuration
File By Using FTP” section on page B-13.
Step 2
Log into the switch through the console port or a Telnet
session.
Step 3
configure terminal Enter global configuration mode.
This step is required only if you override the default remote
username or password (see Steps 4, 5, and 6).
Step 4
ip ftp username username (Optional) Change the default remote username.
Step 5
ip ftp password password (Optional) Change the default password.

Table of Contents

Other manuals for Cisco ME 3400

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco ME 3400 and is the answer not in the manual?

Cisco ME 3400 Specifications

General IconGeneral
CategorySwitch
Rack MountableYes
Jumbo Frame SupportYes
Authentication MethodRADIUS, TACACS+
RAM128 MB
Flash Memory32 MB
Power DeviceInternal power supply
ModelME 3400
LayerLayer 2
MAC Address Table Size8000 entries
Remote Management ProtocolSNMP, Telnet, SSH, HTTP, HTTPS
FeaturesVLAN support, IGMP snooping, Quality of Service (QoS)
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.3x
Memory128 MB
Power SupplyAC 120/230 V (50/60 Hz)
Dimensions (H x W x D)4.4 cm x 44.5 cm x 24.2 cm
Routing ProtocolStatic routing

Related product manuals