EasyManuals Logo

Cisco ME 3400 User Manual

Cisco ME 3400
1138 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #852 background imageLoading...
Page #852 background image
36-16
Cisco ME 3400 Ethernet Access Switch Software Configuration Guide
OL-9639-07
Chapter 36 Configuring IPv6 Unicast Routing
Configuring IPv6
Switch(config)# ipv6 dhcp pool 350
Switch(config-dhcpv6)# address prefix 2001:1005::0/48
Switch(config-dhcpv6)# vendor-specific 9
Switch(config-dhcpv6-vs)# suboption 1 address 1000:235D::1
Switch(config-dhcpv6-vs)# suboption 2 ascii "IP-Phone"
Switch(config-dhcpv6-vs)# end
Enabling the DHCPv6 Client Function
Beginning in privileged EXEC mode, follow these steps to enable the DHCPv6 client function on an
interface.
To disable the DHCPv6 client function, use the no ipv6 address dhcp interface configuration command.
To remove the DHCPv6 client request, use the no ipv6 address dhcp client request interface
configuration command.
This example shows how to acquire an IPv6 address and to enable the rapid-commit option:
Switch(config)# interface gigabitethernet0/1
Switch(config-if)# ipv6 address dhcp rapid-commit
This document describes only the DHCPv6 address assignment. For more information about configuring
the DHCPv6 client, server, or relay agent functions, see the “Implementing DHCP for IPv6” chapter in
the Cisco IOS IPv6 Configuration Library on Cisco.com.
Configuring IPv6 ICMP Rate Limiting
ICMP rate limiting is enabled by default with a default interval between error messages of 100
milliseconds and a bucket size (maximum number of tokens to be stored in a bucket) of 10.
Command Purpose
Step 1
configure terminal Enter global configuration mode.
Step 2
interface interface-id Enter interface configuration mode, and specify the interface
to configure.
Step 3
ipv6 address dhcp [rapid-commit] Enable the interface to acquire an IPv6 address from the
DHCPv6 server.
rapid-commit—(Optional) Allow two-message exchange
method for address assignment.
Step 4
ipv6 dhcp client request [vendor-specific] (Optional) Enable the interface to request the vendor-specific
option.
Step 5
end Return to privileged EXEC mode.
Step 6
show ipv6 dhcp interface Verify that the DHCPv6 client is enabled on an interface.

Table of Contents

Other manuals for Cisco ME 3400

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco ME 3400 and is the answer not in the manual?

Cisco ME 3400 Specifications

General IconGeneral
CategorySwitch
Rack MountableYes
Jumbo Frame SupportYes
Authentication MethodRADIUS, TACACS+
RAM128 MB
Flash Memory32 MB
Power DeviceInternal power supply
ModelME 3400
LayerLayer 2
MAC Address Table Size8000 entries
Remote Management ProtocolSNMP, Telnet, SSH, HTTP, HTTPS
FeaturesVLAN support, IGMP snooping, Quality of Service (QoS)
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.3x
Memory128 MB
Power SupplyAC 120/230 V (50/60 Hz)
Dimensions (H x W x D)4.4 cm x 44.5 cm x 24.2 cm
Routing ProtocolStatic routing

Related product manuals