EasyManuals Logo

Cisco ME 3400 User Manual

Cisco ME 3400
1138 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1008 background imageLoading...
Page #1008 background image
43-14
Cisco ME 3400 Ethernet Access Switch Software Configuration Guide
OL-9639-07
Chapter 43 Configuring MSDP
Configuring MSDP
To remove the filter, use the no ip msdp sa-filter in {ip-address | name} [list access-list-number]
[route-map map-tag] global configuration command.
This example shows how to filter all SA messages from the peer named switch.cisco.com:
Switch(config)# ip msdp peer switch.cisco.com connect-source gigabitethernet0/1
Switch(config)# ip msdp sa-filter in switch.cisco.com
Configuring an MSDP Mesh Group
An MSDP mesh group is a group of MSDP speakers that have fully meshed MSDP connectivity among
one another. Any SA messages received from a peer in a mesh group are not forwarded to other peers in
the same mesh group. Thus, you reduce SA message flooding and simplify peer-RPF flooding. Use the
ip msdp mesh-group global configuration command when there are multiple RPs within a domain. It is
especially used to send SA messages across a domain. You can configure multiple mesh groups (with
different names) in a single switch.
Beginning in privileged EXEC mode, follow these steps to create a mesh group. This procedure is
optional.
To remove an MSDP peer from a mesh group, use the no ip msdp mesh-group name
{ip-address
| name} global configuration command.
Shutting Down an MSDP Peer
If you want to configure many MSDP commands for the same peer and you do not want the peer to
become active, you can shut down the peer, configure it, and later bring it up. When a peer is shut down,
the TCP connection is terminated and is not restarted. You can also shut down an MSDP session without
losing configuration information for the peer.
Command Purpose
Step 1
configure terminal Enter global configuration mode.
Step 2
ip msdp mesh-group name {ip-address |
name}
Configure an MSDP mesh group, and specify the MSDP peer belonging
to that mesh group.
By default, the MSDP peers do not belong to a mesh group.
• For name, enter the name of the mesh group.
• For ip-address | name, enter the IP address or name of the MSDP
peer to be a member of the mesh group.
Step 3
end Return to privileged EXEC mode.
Step 4
show running-config Verify your entries.
Step 5
copy running-config startup-config (Optional) Save your entries in the configuration file.
Step 6
Repeat this procedure on each MSDP peer in the group.

Table of Contents

Other manuals for Cisco ME 3400

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco ME 3400 and is the answer not in the manual?

Cisco ME 3400 Specifications

General IconGeneral
CategorySwitch
Rack MountableYes
Jumbo Frame SupportYes
Authentication MethodRADIUS, TACACS+
RAM128 MB
Flash Memory32 MB
Power DeviceInternal power supply
ModelME 3400
LayerLayer 2
MAC Address Table Size8000 entries
Remote Management ProtocolSNMP, Telnet, SSH, HTTP, HTTPS
FeaturesVLAN support, IGMP snooping, Quality of Service (QoS)
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.3x
Memory128 MB
Power SupplyAC 120/230 V (50/60 Hz)
Dimensions (H x W x D)4.4 cm x 44.5 cm x 24.2 cm
Routing ProtocolStatic routing

Related product manuals