EasyManuals Logo

D-Link DWC-1000 Reference Guide

D-Link DWC-1000
146 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #49 background imageLoading...
Page #49 background image
Wireless Controller CLI Reference Guide
47
8.22 wlan client delete <macaddr>
S.No
Command Name
Description
Type and Description
1
<macaddr>
w lan client configuration mode
MAC address
AA:BB:CC:DD:EE:FF where
each part is in the range 00-
FF
8.23 wlan global dist_tunnel configure
S.No
Command Name
Description
Type and Description
1
save
Save Distributed Tunneling settings.
2
exit
Save Distributed Tunneling settings and exit
current mode.
3
cancel
Roll back Distributed Tunneling settings
changes.
4
max_clients
Enter maximum client connections supported.
Unsigned integer
5
idle_timeout
Enter idle timeout value in seconds.
Unsigned integer
6
max_timeout
Enter maximum timeout value in seconds
Unsigned integer
7
mcast_reply
Enter maximum multicast relplications
allow ed.
Unsigned integer
8.24 wlan global snmp_trap configure
S.No
Command Name
Description
Type and Description
1
save
Save SNMP Trap settings.
2
exit
Save SNMP Trap settings and exit current
mode.
3
cancel
Roll back SNMP Trap settings changes.
4
ap_failure
Enable/Disable SNMP traps for AP
association/authentication failures.
Boolean choice
5
ap_state
Enable/Disable SNMP traps for AP state
changes.
Boolean choice
6
client_failure
Enable/Disable SNMP traps for client
association/authentication failures.
Boolean choice
7
client_state
Enable/Disable SNMP traps client state
changes
Boolean choice
8
peer_w s
Enable/Disable SNMP traps for peer w lan
sw itch events.
Boolean choice
9
rf_scan
Enable/Disable SNMP traps for RF scan
related events.
Boolean choice
10
rogue_ap
Enable/Disable SNMP traps for rogue access
points.
Boolean choice
11
tspec
Enable/Disable SNMP traps for TSPEC
related events.
Boolean choice
12
w ids_status
Enable/Disable SNMP traps for WIDS status
events.
Boolean choice
13
w s_status
Enable/Disable SNMP traps for ws status
events
Boolean choice
8.25 wlan global configure
S.No
Command Name
Description
Type and Description

Table of Contents

Other manuals for D-Link DWC-1000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the D-Link DWC-1000 and is the answer not in the manual?

D-Link DWC-1000 Specifications

General IconGeneral
Ethernet LANYes
Wi-Fi standards802.11a, 802.11b, 802.11g
Networking standardsIEEE 802.1Q, IEEE 802.1x, IEEE 802.3, IEEE 802.3ad, IEEE 802.3u
Ethernet LAN data rates10, 100, 1000 Mbit/s
Number of managed Wi-Fi Access Points (max)6
Security algorithms3DES, DES, WEP, WPA, WPA2
USB 2.0 ports quantity2
Ethernet LAN (RJ-45) ports4
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity0
CertificationFCC B, CE B, VCCI, C-tick, IC, cUL, LVD (EN60950-1)
Built-in displayNo
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)5 - 95 %
Power requirementsDC 12V/2.5A
Power consumption (typical)19.3 W
Pallet width1200 mm
Pallet length1100 mm
Pallet height (air)1419 mm
Pallet height (sea)1847 mm
Pallet gross weight (air)415236 g
Pallet gross weight (sea)545648 g
Quantity per pallet (air)144 pc(s)
Quantity per pallet (sea)192 pc(s)
Shipping (inner) case width296 mm
Shipping (inner) case height428 mm
Shipping (inner) case length354 mm
Shipping (inner) case weight10826 g
Shipping (inner) case net weight10016 g
Number of cartons per pallet (air)36 pc(s)
Number of cartons per pallet (sea)48 pc(s)
Quantity per shipping (inner) case4 pc(s)
Weight and Dimensions IconWeight and Dimensions
Package depth396 mm
Package width273 mm
Package height80 mm
Package weight2504 g
Dimensions (WxDxH)280 x 180 x 44 mm

Related product manuals