EasyManuals Logo

Extron electronics CrossPoint 450 Plus Series User Manual

Extron electronics CrossPoint 450 Plus Series
214 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #197 background imageLoading...
Page #197 background image
B-7
CrossPoint / MAV Matrix Switchers • Reference Information
Maximum level ������������������������������ +21 dBu, (balanced or unbalanced) at 0�01% THD+N
Input gain adjustment ������������������ -18 dB to +24 dB (default = 0 dB), adjustable per input by RS-232/422,
Ethernet, or front panel
N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu
Audio output— audio models only
Number/signal type ��������������������� 4, 8, 12, or 16 stereo, balanced/unbalanced
Connectors ������������������������������������� (4, 8, 12, or 16) 3�5 mm captive screw connectors, 5 pole
Impedance �������������������������������������� 50 ohms unbalanced, 100 ohms balanced
Gain error ��������������������������������������� ±0�1 dB channel to channel
Maximum level (Hi-Z) ����������������� >+21 dBu, balanced or unbalanced at 1�0% THD+N
Maximum level (600 ohm) ����������� >+20 dBm, balanced or unbalanced at 1�0% THD+N
Output volume range ������������������� 0 to 64 (-75�8 dB to 0 dB) in 1 dB increments from steps 1 to 64, in 12 dB
increment from step 0 to 1; default = 64 = 0 dB
Control/remote — switcher
Serial host control port ����������������� 1 bidirectional RS-232 or RS-422, rear panel 9-pin female D connector
1 bidirectional RS-232, front panel 2�5 mm mini stereo jack
Baud rate and protocol ����������������� 9600 (default), 19200, 38400, 115200 baud (adjustable); 8 data bits, 1 stop bit,
no parity
Serial control pin configurations
RS-232 ��������������������������������� 9-pin female D connector: 2 = Tx, 3 = Rx, 5 = GND
Mini stereo jack: tip = Tx, ring = Rx, sleeve = GND
RS-422 ��������������������������������� 9-pin female D connector: 2 = Tx-, 3 = Rx-, 5 = GND, 7 = Rx+, 8 = Tx+
Ethernet control port��������������������� 1 RJ-45 female connector
Ethernet data rate �������������������������� 10/100Base-T, half/full duplex with autodetect
Ethernet protocol ��������������������������� ARP, DHCP, ICMP (ping), TCP/IP, Telnet, HTTP, SMTP
Ethernet default settings �������������� Link speed and duplex level = autodetected
IP address = 192�168�254�254
Subnet mask = 255�255�0�0
Default gateway = 0�0�0�0
DHCP = off
Web server �������������������������������������� Up to 200 simultaneous sessions
1�24 MB nonvolatile user memory
Program control ����������������������������� Extron control/configuration program for Windows
®
Extron Simple Instruction Set
(SIS
)
Microsoft
®
Internet Explorer
®
, Telnet
General
Power ���������������������������������������������� 100 VAC to 240 VAC, 50-60 Hz, internal, primary and redundant
84/88/128 Series ��������������� 35 watts (typical)
38 watts (loaded)
1212/168/1616 Series ������� 45 watts (typical)
52 watts (loaded)
Temperature/humidity ���������������� Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling ������������������������������������������� Convection, no vents
Mounting
Rack mount
������������������������ Yes
Enclosure type ������������������������������� Metal

Table of Contents

Other manuals for Extron electronics CrossPoint 450 Plus Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Extron electronics CrossPoint 450 Plus Series and is the answer not in the manual?

Extron electronics CrossPoint 450 Plus Series Specifications

General IconGeneral
BrandExtron electronics
ModelCrossPoint 450 Plus Series
CategoryMatrix Switcher
LanguageEnglish

Related product manuals