Fostex DMT-8VL - Page 141

DMTSVL Owner's Manual (MMC/FEX List/Maintenance/Specificalions)
Explanation on the Command/Mode Set
12 22 (<on/off>): loop on/off command
The command for setting the loop mode on/ofT (-ON/OFF of AUTO RTS) of D-80/
l>SfT-8 ver2.0ZDMT-8 vl Default figure of the loop operation mode is "12-stop" and this
cannot he changed.
12 28 (<poat locate mode>): post locate command
The command for setting the "post locate mode" (-ON/OFF of AUTO PLAY) of D-80/
DSfT-8 ver2.0/DMT-8\z. It \>ill stop after locating if m post locate mode-12. * It will enter
play after locating if *post locate mode-IS."
12 2D (<on/off>): auto rec command
The command for setting "auto rec mode on/ofT' (-OS/OPT of AUTO PUNCH) of D-80/
Dbff-8 ver2.0/DSfT-8 vl Upon receiving this command, D-80/DMT-8 ver2.0/DMT-8vi
will immediately reply the operating condition by sending "32 2D (<ed!t message >)\
12 41 (clock anable>): lock enable command
The command for setting *slave mode on/ofT % (setup menu) of D-80/DMT-8 ver2.0/
DMT-Svl
12 45 (ccountxmmc track>): copy clip command
When this command is received, D-80/DMT-8 ver2.0/DbfT • 8vl will copy (multiple number
of tracks can be copied simultaneously) the sound data, as data for copy paste , from the
pre-registered clipboard-in point to the clipboard out point In the track specified by
<mmc track>.
With completion of copying the data into the clipboard. D-80/DMT-8 ver2.0/DMT-8vi
will immediately reply with "32 45 (<cdit message-01 (completed)>)”.
If copy cannot he executed due to improper figures of (be pre-registered clipboard In/
clipboard out points or incorrect track section, the corresponding <edit message> will he
returned.
12 46 (<count= 1><repeat count>): copy pasta command
12 46 (<count><rapaat countxmmc track>): copy paste command
When this command is received, D-80/DMT-8 ver2.0/DMT-8vL will paste the sound data
which has been copied into the clipboard, on the same track from the pre-registered auto
punch in point ever, if the sound data length In the clipboard is less than IOms, the
specifying the <repcat count> will be limited to "01. *
Also, by specifying <mmc track>, paste can be executed on other tracks in mono (in one
track units) or stereo units (in combinations of tracks 1 A 2, 3 A 4, 5 A 6, 7 A 8).
Since time corresponding to length of the copy clipped sound data is required to complete
the copy paste operation, D-80/DMT-8 ver2.0/DMT-8vL Immediately replies with "32
46{<cdit message-02 (active)>)" after receiving the command.
Successively upon completing the paste operation, "32 46 (<edit message-01
(completed)>)"is transmitted.
If paste cannot he executed due to improper figures of the pre-registered auto punch in
point, insufficient disc capacity, no sound data in the clipboard, etc., the corresponding
<cditmessage> will be replied.
12 47 (<countxmmc track>): erne command
When this command is received. D80/DMT-8 ver2.0/DMT-8\z will erase the data (writes
in "0" data) in the section from the pre-registered auto punch in point through auto
punch out point in the track specified by <mmc track>. Since time corresponding to
length of the erase section Is required to complete the erase operation. D-80/DMT-8 will
immediately reply by "32 47 (<edit message-02 (acdve)>)" after receiving the command
141