Fostex DMT-8VL - Page 142

DMT-8VI Owner's Manual (SfMC/FEX Ust/Maintcnancc/Specifications)
After the completion of erase operation. "32 47 (<cdtt message ^ 01 (completed)>) n will
be transmitted
If erase cannot be executed due to improper figures of the pre-registered auto punch in
point/autopunch outpoint. incorrect track section, Cft., the corresponding <cdrt message »
Will be replied.
12 48: cut
When this command Is received. D-80/DMT-8 vc r2.0/DMT-8\iwill cut whole the section
following the pre-recorded auto punch in point under the assumption that whole the
tracks are nonrecorded section. With completion of the cut operation , this equipment
will immediately reply with "32 48 (<edit message ^OJ (completed)>).* If cut Is
uncxecutablc due to improper figure of the pre-reglstered auto punch in point, the '
corresponding <edit message* will be replied.
12 49: clipboard play
When this command is received. D-80/DMT-8 ver2.0/DMT-8\i will playback once from
the head of the sound data copied in the clipboard by the copy clip and move dip
commands.
Immediately after receiving the command. D-80/DSTT-8 ver2.0/DMT-8vi will reply with
*32 49 (<edit message-02 (active)xmmc track>).* The sound data track number is
indicated by (mmc track>.
Upon completion of playback “32 49 (<edlt message-Ol (completed) is sent and clipboard
play is ended. If there is no sound data in the clipboard. "32 49 (<edil message-14 (void
data)>T will be sent and clipboard play operation will be interrupted.
12 4A: undo
Upon receiving this command. D-80/DMT-8 vvr2.0/DMT-8\z will revert to the condition
prior to editing copy pastc.crase, move paste, cut. redo operation. With completion of
undo operation. D-80/DMT-8 ver2.0/DMTSVLwtil reply with "32 4A (<edit message
-01 (completed )>)."
If D-80/DMT-8 ver2.O/DMT-8\z is not possible to undo. "32 4A (<edlt message-00 (no
message )>)* will be replied.
12 4B: redo
When this command is received. D-80/DMT-8 ver2.0/DSTT-8vi will return to the condition
prior to undo operation.
With completion of redo operation, D-80/DMT-8 ver2.0/DMT-8 vl will reply with "32 48
(<edlt message-01 (completed)>).*
If D-80/DSTV-8 ver2.0/DSfT-8vr is not possible to redo, *32 48 (<cdit mcssagc-00 (no
message^)* will be replied.
12 4C: (<on/off>): nondes. mode
The command for setting on/off of non destructive mode on D-HO/DMT-8.
if <on/off> is set to "on,* recording mode of D-80/DMT--8 ver2.0/DMT-8vi will enter the
non destructive mode,and it "off." in the destructive mode .
Nondes. mode:
Abbreviation for "non destructive recording mode". When this mode is ON. not only
"takes" made by various sound editing or AtJTO PUNCH IN/OUT but "takes" retarded by
simultaneous pressing of the PLAY and RECORD burtons (direct recording) will always be
possible to UNDO (However, free disc memory space equivalent to the recording length
will always be required ). This is the same function of switching between "undo: All
(Nondes mode.on) -—* Edit (Nondcs.mode:off) % ' in the setup menu on the mam unit .
142