Fostex DMT-8VL - Page 143

DMT-8vl Owner's Manual (MMC/FEX Ust/Malntenance/Speclflcations)
12 40 (<counixmmc track>): move clip command
When this command is received . D-80/DMT - 8 vc r2.0/DMT~8\l will copy (multiple tracks
can be copied simultaneously) the sound data from the pre-reg/stcrcd clipboard in point
to the clipboard out point, as data for move paste operation.
With completion copying the data into the clipboard, D'80/DMT-8 ver2.0/DF1T-8\r will
immediately reply with "32 4D (<edit message-Ol (completed)>)."
If copy cannot be executed by the reason of pre-registered improper clipboard in/dlpboard
out point figures or incorrect track section, etc,, the corresponding <edit message> will
be replied.
12 4E (<countB Ixrepeat count>): move paste command
12 4E (<countxrepea1 countxmmc track>): move paste command
When this command is received, D-80/DMT-8 ver2.0/DMT-8\l will paste the sound data
which have been move clipped in the clipboard, for the number of times specified by
<repeat count> on the same track from the pre-registered auto punch in point as the
starting point.
At (he same time , the move clipped original sound data will be erased (data "0* is written
in). However; when sound data length In the clipboard is less than 10ms, specifying
the <repeat count> will be limited to "01."
Also, by specifying the <mmc tracks paste operation can be executed on other tracks in
mono (one track unit) or stereo units (tracks l & 2. 3 & 4. 5 & 6.7 & 8).
Since time corresponding to length at the move clipped sound data is required to complete
the move paste operation. D-80/DMT-8 ver2.0/DMT-8\l will immediately reply with *32
4E (<edit message-02 (active)>) m after receiving the command.
Following completion of the move paste operation . "32 4E (<edit message - 01
( completed )>)” will be sent.
If paste cannot be executed due to Improper figures of the previously registered auto
punch in point, insufficient disc capacity, no sound data is In the clipboard, etc., the
corresponding <edit message:- will be replied.
13 41 (<channetxchannel>): digital in ch.select command
The command assigning the digital audio signal (5/P DIE) Input from the D-80/DMT-8
vcr2.0/DMT-8\i DATA IN connector to the track specified by <t hanneb. The digital
audio signal L channel assignment point is specified by the first <channel> and the R
channel assignment point by the second <channel> in the command. If the same figure
is specified for both <channels>. L channel will have priority and R channel will be
(invalid).
13 42 (<channetxchennef>): digital out ch.seiect command
This command selects the soune track for the digital audio signal (S/P DIF) output from
the D-80/DMT-8 ver2.0/DSfT-8vL DATA OUT connector.
Normally. the track specified by the first <channc/> will be the digital audio signal L
channel data, and the track specified by the second <channel> will be the digital audio
signal R channel data. In this equipment, the five types • (<0I><02>), (<03><04>).
(<05><06>). (<07><08>) and (<00><0Q>) - can only be set up. Also, when (<00><00>) is
specified, default (L-. R>. No Assign) will be set up in D-80, and (LL. RJO will beset up in
DMT*8 \vr2.0/DMT-8vi. Thus the mixer section stereo bus output will be assigned on
DMT-8 ver2.0/DMT-8v l
13 43(<program>): program change command
The command for PROGRAM CHANGE of 80/DMT-8 wr2.0/DMT-8\r. The present
program number can be changed to the figure indicated by <program>.
143