EasyManuals Logo

Honeywell Thor VM3 User Manual

Honeywell Thor VM3
378 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #209 background imageLoading...
Page #209 background image
Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide 197
Power Configuration Mode
Start > Settings > Control Panel > Power Configuration Mode
There are three user selectable power configuration modes for the Thor VM3 available.
Additionally a UPS power configuration mode is supported and automatically selected
regardless of the user selected mode any time external power is not present.
Power control panel timeout values vary by the power configuration mode selected.
AC/DC Mode
This is the default power mode. In AC/DC mode the Thor VM3 is turned On when power
is connected. Ignition input is ignored when AC/DC Mode is enabled.
Note: When the UPS battery has been depleted or disconnected (the Thor VM3 is first powered
out of the box, the front panel has been replaced, etc.) power the Thor VM3 manually by
pressing the power button. After the initial power up, the Thor VM3 powers on
automatically when power is attached and AC/DC mode is selected.
Note: When AC/DC is used to power the Thor VM3 on automatically the Wakeup Timer must be
enabled.
Thor VM3 is Off
Conditions
The Thor VM3 is Off and gets external power, such as
Thor VM3 is installed on a powered dock with the dock power switch On
Thor VM3 is already mounted to a dock and external power is applied to the dock
Thor VM3 is already mounted to a dock and the dock power switch is turned On
Result
The Thor VM3 boots. Once booted the Thor VM3 follows the AC/DC power scheme with
timers reset after the boot completes.
Thor VM3 is On
Conditions
The Thor VM3 is On and gets external power, such as
Thor VM3 is installed on a powered dock with the dock power switch On

Table of Contents

Other manuals for Honeywell Thor VM3

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Honeywell Thor VM3 and is the answer not in the manual?

Honeywell Thor VM3 Specifications

General IconGeneral
SteppingD0
Tjunction-40 °C
FSB ParityNo
Processor codeSR1X8
Processor cache1 MB
Processor cores2
Processor modelE3826
System bus rate- GT/s
Processor familyIntel Atom®
Processor codenameBay Trail
Processor frequency1.46 GHz
Processor cache typeL2
Processor manufacturerIntel
Processor package size25 x 27 mm
Conflict-Free processorYes
Processor front side bus- MHz
Processor operating modes32-bit, 64-bit
Graphics & IMC lithography22 nm
PCI Express configurations1x1, 1x4, 2x1
Thermal Design Power (TDP)7 W
Internal memory4 GB
Internal memory typeDDR3-SDRAM
Storage mediaFlash
Compatible memory cards-
Internal storage capacity64 GB
Display diagonal12.1 \
Display brightness900 cd/m²
Display resolution1024 x 768 pixels
Graphics cardHD Graphics
Rear camera resolution (numeric)- MP
Wi-Fi standards802.11a, 802.11b, 802.11g
Bluetooth version2.0+EDR
Top Wi-Fi standardWi-Fi 4 (802.11n)
HDMI ports quantity0
USB 2.0 ports quantity1
I/O ports1x CAN-bus, RF
Processor ARK ID78477
Processor socketBGA 1170
Operating temperature (T-T)-30 - 50 °C
Operating relative humidity (H-H)5 - 95 %
PlatformWindows
Bundled softwareData Collection Engine, Microsoft Internet Explorer, Microsoft on-screen keyboard, Configuration Cloning Utility, Screen Blanking, Zoom Zone, Launcher
Operating system installedWindows 7
AC adapter input voltage90 - 240 V
Battery capacity- mAh
Battery life (max)0.5 h
CertificationEN 55024:2010, MIL-STD-810F, SAE-J1455, CCX
Device typeTablet PC
Form factorSlate
Product colorGrey, Silver
Protection featuresShock resistant, Vibration proof, Water resistant
International Protection (IP) codeIP66
Harmonized System (HS) code84713000
Weight and Dimensions IconWeight and Dimensions
Depth62 mm
Width318 mm
Height260 mm
Weight3000 g

Related product manuals